Do-it-yourself plow for a walk-behind tractor: types and properties of shovels for snow removal, drawings with dimensions and a step-by-step algorithm for manufacturing from a barrel and a cylinder

With the onset of cold weather, private farm owners are faced with the problem of snow removal. Previously, snow shovels were used for this; nowadays, almost every household has a walk-behind tractor, which can be adapted for these purposes using a special blade. You can buy a shovel blade (blade) in a specialized store (which is quite expensive), or you can make it yourself. By making such equipment yourself, you will save quite a significant amount and will not spend a lot of time.

Description of the blade for the walk-behind tractor

A blade (blade blade, shovel attachment) is a mounted tool in the form of a shovel or bucket, which is mounted on a walk-behind tractor for the purpose of removing snow and debris from a flat surface, and can also be used to level land for planting vegetables or a lawn.

It is a universal equipment, it can be used with any model of walk-behind tractor, without being tied to the power characteristics of the engine. The factory-made blade attachment has the following dimensions: width – 100 cm, height – 40 cm, however, for handicraft production, any dimensions can be selected.

When manufacturing a blade, you need to select such dimensions so that the load on it corresponds to the power of the walk-behind tractor. The use of a tool whose design is designed with too much performance can lead to overload of the unit and its failure.

Rotary

A snow blower of this type is represented by a mounted model, fixed to a walk-behind tractor. The technique is used only in winter, as it copes with any type of snow mass due to its design (stay and freshly fallen snow, ice, crusty drift, passage through deep snow). The main element is the rotor, made of a shaft with bearings and blade impellers.

There are up to 5 blades in the design; it is possible to manually install more or less blades based on the needs of cleaning the area.

A pulley (made from a V-belt) rotates the blades when the walk-behind tractor moves.

The bearing metal hub is fixed on the side sections of the housing. The visor pipe, located in the side wall of the upper part of the equipment, throws snow out.

Rotary snow blowers work by sucking snow using blades and air flow, which is generated by the rotation of impellers. The height of the emission of snow masses reaches 6 meters. One of the disadvantages of the cleaner is the lack of ability to remove compacted snow. The width of the finished passage of rotary equipment is half a meter.

Why do you need a blade for a walk-behind tractor?

Using a blade you can perform the following basic work:

clear snow drifts;
level the surface of the earth;
remove trash;
perform loading operations (if the blade is in the form of a bucket).

A walk-behind tractor with such a hitch can also be used for:

creating landscape design;
construction of roads and paths;
quick digging of trenches, wells and ravines;
creating high beds;
collecting bulk materials for their subsequent transportation in a cart (trailer);
spreading soil or organic fertilizers around the site.

As can be seen from the list of works, the dump can be used all year round.

Sheet steel shovel

Some craftsmen prefer to use new material rather than used elements. This way you can assemble a homemade blade from an iron sheet 3 mm thick. To strengthen the device, you can use a steel strip with a thickness of at least 5 millimeters. Metal cutting is carried out according to diagrams. The blade of the blade itself contains 4 segments: front, bottom and 2 side. The assembled structure requires reinforcement. To do this, components cut from metal 5 mm thick are welded vertically.

Then a rotating device is created. It is an eye with a hole for the axle. The eye is fixed by welding to a corner that is attached to the shovel. The axis is fixed on one edge of the pipe, and the other edge is fixed on the walk-behind tractor. The required degree of rotation is fixed by a cylindrical rod (dowel). 3 millimeters is a small thickness, which means it needs to be strengthened. Cut a strip of 850x100x3 mm from a sheet 3 mm thick.

You can fix it with bolts, but you will need to drill or weld the strip first.

To carry out the work you will need:

sheet metal;
angle grinder with discs;
electric drill;
set of drills;
bolts with self-locking nuts (with plastic inserts);
welder with electrodes;
wrenches;
profile or round pipe.

If you have the necessary abilities, the work is not difficult. And the created device can be used not only in winter, but also in summer. Improve the site after completion of construction and installation work, plan the area for a children's sandbox, etc. What type of construction to choose is up to you to decide.

To learn how to make a blade blade for the Neva MB-2 walk-behind tractor, see the video below.

Blade classification

This simple mounted implement has the following classification:

According to execution form:
bucket (hemispherical, spherical, spherical for bulk materials).
According to the method of attachment to the walk-behind tractor:
using lugs and locks.
According to the location of the working body relative to the walk-behind tractor
rear (if the steering column can be rotated 180 degrees).
By hitch type:
unregulated.
By type of lifting mechanism:
hydraulic.

What it is?

The walk-behind tractor is similar to a mini-tractor; its real participation in work begins with equipping it with attachments. The “symbiosis” of the engine and all kinds of attachments allows you to plow, loosen, chop wood, transport cargo, mow grass, and clear snow. All these devices can be placed on a walk-behind tractor and you will get a miniature excavator, tractor or lawn mower.

A walk-behind tractor is often confused with a cultivator, both of which carry out pre-planting work on the ground.

But it should be understood that the capabilities of the first are much wider than the second, although they completely depend on the attachments. A walk-behind tractor is more powerful than a cultivator; its traction is due to the wheels. It also has an engine, often internal combustion, a transmission that regulates the speed and gearbox, and a steering wheel (remote control). As you can see, the device is simple and can be repaired independently.

Various types of attachments are purchased for the walk-behind tractor, for example, stationary equipment is mounted on an adapter. The activator depends on the rotational power of the gearbox. On axial equipment, the nozzles rotate under the weight of the walk-behind tractor. Landing and steering accessories refer to adapter attachments.

Blade design features

Structurally, the walk-behind blade is a curved metal surface and consists of the following elements:

working body (the shovel itself or the bucket);
fastening unit;
mechanism for adjusting the angle of rotation of the working body.

As a rule, the shovel attachment is fixed in one of three positions during operation:

directly;
with a rotation of 30 degrees. left;
with a rotation of 30 degrees. to the right.

Before starting work on the manufacture of a blade, carefully analyze the available recommendations and read the literature on this topic.

Some points to pay attention to when creating a blade for a walk-behind tractor

The manufactured product must meet the following criteria:

Reliability. The strength characteristics of the knife and shovel must be high enough for the device to last as long as possible without repair. For the manufacture of all parts, it is necessary to select such materials, the use of which would ensure the maximum load on the device, but not exceeding the limit values for the power plant of the unit.
Dimensions. Factory dumps have standard dimensions, but if you make them yourself, you can make them whatever you want. Of course, you want to make the tool as productive as possible, but you shouldn’t go too far beyond the standardized dimensions. This can lead to overload of the motor and damage to the walk-behind tractor.
Availability of a lifting mechanism. It is needed to expand the possibilities for using the blade, since if it is available, it will be possible not only to clear snow and remove garbage, but also to remove it from the site. Also, the lifting mechanism will be useful, for example, when loading bulk materials onto a cart or moving them around the site. There are only two types of lifts: mechanical (the position of the shovel is changed manually using a lever) and hydraulic (using a hydraulic pump). A mechanical lift is not difficult to implement; a hydraulic lift will take a little more work, but it is also quite simple.
The presence of a swivel joint. If it is possible to adjust the shovel vertically and horizontally, then snow removal will be more efficient.
Security. A thick rubber strip on the blade of the blade will protect the device from impacts, breakages and deformations, and the surface being processed from damage.
Quick installation/dismantling. Sometimes you need to quickly change the attachment to a walk-behind tractor; therefore, it is advisable to provide for this possibility when creating the mounting of the blade to the unit.

The rounded top allows the blade to roll the snow in front of it rather than simply moving the snow mass. Thus, the walk-behind tractor needs to use significantly less force than with a straight shovel.

Factory models

Any company that manufactures walk-behind tractors can also offer a range of snow plows. There are popular models on sale from such manufacturers as Centaur, Neva, Zirka, etc. The only big advantage of a factory design over a home-made one is that they are made of high-quality steel and are more difficult to damage. Moreover, such models last longer than homemade ones. But, on the other hand, they cost a lot.

There are a lot of options for factory dumps, so you should check before purchasing whether this model is suitable for your existing walk-behind tractor. At the factory, snow plows are not equipped with spring mechanisms due to the low speed of movement. If the speed of the walk-behind tractor is low, then the protective mechanisms for contact with the ground lose their meaning. Moreover, the factory models do not have mechanisms for lifting and turning the unit. In this regard, the price of the factory design is reduced.

For higher performance, it is recommended to replace conventional rubber wheels with factory or homemade lugs. This will speed up the work process.

Prices for snow blowers may vary. Basically, the cost of these varies from 4 thousand to 6 thousand rubles.

Required tools and materials

In order to make a blade for a walk-behind tractor with your own hands, you will need:

Materials:

To create a working surface, a 200-liter steel barrel, an empty gas cylinder or a sheet of iron is suitable;
iron piece 5 mm thick;
a piece of pipe with a square cross-section of 40x40 mm and a length of 1 m;
a strip of thick durable rubber;
sheet steel 10-12 mm thick;
fasteners (bolts, nuts).

Tools:

roulette;
welding machine;
angle grinder (grinder);
drill with a set of drills;
a set of wrenches, a hammer, pliers and other plumbing tools.

Advice from professionals

When assembling a blade blade for a walk-behind tractor with your own hands, experts advise using sheet steel 3 mm thick. Thin sheet metal will bend under load. Thick metal will increase the weight of the hitch, which will create additional load on the walk-behind tractor engine.

Rubber for the knife is a must. It is attached so that the edges touch the edge of the metal bus. With this arrangement, the rubber wears off less and prevents the steel blade from destroying the hard paving surface.

When clearing snow drifts, anti-slip chains or lugs are placed on the wheels of the walk-behind tractor.

A walk-behind tractor with a mounted blade is optimal for removing snow drifts more than 50 mm thick. If there is not enough snow, instead of a shovel it is better to use another attachment - a brush. To prevent the wheels from slipping, wear anti-slip chains. When cleaning an area without a hard surface, instead of transport wheels, you can install metal devices - lugs.

During cleaning, do not allow the walk-behind tractor engine to overheat. Periodically it is given time to cool down. If the snow is wet, the shovel quickly sticks. It needs to be cleaned more often. In case of damage to the blade or towbar, work continues after the defect has been eliminated. Otherwise, when some parts are bent, the entire attachment will become distorted, which will lead to serious damage.

Features of making a blade for a walk-behind tractor with your own hands step by step

The blade can be made in different ways from different materials. Let's consider the 2 most popular:

from a steel 200-liter barrel;
from a gas cylinder;

Drawings with dimensions

Blade
Left knife
Medium knife
Bolt
Washer 16.65G.019 GOST 6402-70
Nut M16-6N.5.019 (S24) GOST 15523-70
Bolt
Right knife
Washer 20.65G.019 GOST 6402-70
Nut M20-6N.8.019 (S30) GOST 15523-70

Blade from a barrel

Let's take a step-by-step look at how to make a shovel for a walk-behind tractor using a metal barrel:

Take an old 200 liter barrel and cut off the lid and bottom with a grinder.
Apply markings to the barrel so that you get 3 identical sectors of 120 grams each. After that, cut it with a grinder.
Connect the two segments at their ends with an overlap of 3 cm using a welding machine. Next, you need to strengthen the structure. To do this, cut the remaining part of the barrel into strips with a grinder. Attach one strip to the sides of the shovel, distribute the rest evenly along the entire length of the working body. You can also use a profile pipe.
To protect the working surface of the blade, a knife is installed in its lower part. To do this, you will need a metal strip the same length as the grip of the shovel, 100 mm wide and 5 mm thick. Using an electric drill, make holes in the knife with a diameter of 5-6 mm at intervals of 100-120 mm for mounting the rubber strip.
Place the rubber strip on the knife. It is better to make the width of the protruding part from 3 to 10 cm. The tape should be removable so that the blade can be used for working with bulk materials.
Next, we attach the shovel to the walk-behind tractor. Make a U-shaped part from sheet iron (you can take a suitable channel).
Make several holes in the resulting U-shaped part to set the required angles of rotation of the shovel. We also make holes for attaching a square metal profile.
Weld the resulting part in the center of the work surface.
Now you need to make an adapter. Take another piece of square pipe and make an L-shaped part from it. The short side of this adapter is attached to the U-shaped part, and the other end of the pipe is bolted to the walk-behind tractor frame.
To adjust the height of the blade, weld two eyes to the lower profile (which is connected to the rotary sector) and a metal plate to the upper one (which is fixed to the walk-behind tractor bracket). Make a hole in the plate for the bolt. Take a piece of pipe and drill a hole. One end of this pipe will be bolted to the down pipe, and a bolt or threaded rod will be welded to the other end. Thread the bolt into the hole in the metal plate to make a handle.
A shovel for a walk-behind tractor for clearing snow with your own hands is ready.

It should be taken into account that the thickness of the barrel walls is small. It is better to use such a blade for cleaning recently fallen snow, which has not yet compacted and is not covered with an ice crust.

Blade from a gas cylinder

Using a cylinder, a motorized cultivator-snow blower is made in the same way as from a barrel with minor differences. Assembly order:

Release excess pressure from the cylinder.
Cut off the caps from the ends of the cylinder so that the width of the resulting pipe is 1 m.
Cut this pipe lengthwise into two equal parts.
By welding, fasten the 2 parts so that the height of the blade is about 700 mm.
Make a hitch.

Since the walls of the cylinder are quite strong (thick), their additional strengthening is not required. With such a blade, the walk-behind tractor will be able to work with compacted snow, level the surface, move sand and crushed stone without fear of damaging the working surface of the shovel.

Preparing for work

You can install a snow blade on the frame of any motorized cultivator with a power of at least 4 liters. With. and weighing more than 50 kg. Also, by reviewing the drawings of a plow for a mini-tractor with your own hands, you can adjust them to your needs if you have a mini-tractor on the farm

It is important for this unit that it is not lightweight. The heavier it is, the easier it will be to rake snowdrifts

The domestically produced Neva walk-behind tractor is well suited for this type of work. The equipment has a high performance coefficient. The walk-behind tractor is adapted to harsh weather conditions at maximum loads.

In the process of making a shovel for a walk-behind tractor, you will need the following tools:

Welding
Roulette
Grinder with cutting and grinding discs for metal
Electric drill
A set of keys
Screwdriver
Paint brushes and paint

Having completed the preparation of the tool, you can begin to select the material for making the device. Many metal products with a good strength rating can be suitable for this.

The shovel can be made from such materials

Inoperative gas cylinder. The walls of the product are made of thick and durable metal, so having made such a dump, it will be possible to remove compacted snow, level the ground, rake crushed stone and sand.
Large barrel with a capacity of 200 l. When choosing such a material, you need to remember that the steel of the product is not thick, and such material can only withstand removing snow that has recently fallen and is not compacted.
Metal strips. For manufacturing, truck bumpers or corrugated steel for covering the floor of production facilities may be suitable.

To make a snow dump, you can also use Zykov’s plow, drawings and dimensions. As a material for the rotating mechanism, you need to choose steel with a thickness of more than 10 mm. Such material is easy to find at scrap metal collection sites. For fastening you will need a steel pipe profile of approximately 20x40 mm.

When working with loose snow and deep hillocks, the equipment can get stuck and slip. This problem is solved by installing tracks on the axle shaft of the tractor. After this, you can work with the snow blower in any conditions without losing productivity.

Rules for using a homemade blade

Follow these rules and your equipment will last longer:

To save the resource of the power plant, use the blade only if it is necessary to remove snow more than 5 cm high. In other cases, it is better to use a sweeping brush or scraper.
When working with a blade, it is advisable to equip the wheels with tracks or other devices that increase the traction of the walk-behind tractor with the surface.
Periodically check the motor of the walk-behind tractor - when working with mounted implements, it is subject to increased load and wear.
Regularly check the reliability of the fasteners; if any defects appear, replace them immediately.
To prevent deformation and breakage of the blade, before starting work, carefully set the height of its position;
Use protective equipment, both for yourself and for your equipment. For example, steel guards can be used to protect the unit.
Carry out regular maintenance of the walk-behind tractor and additional attachments (the frequency is indicated in the instructions for use).
At the end of the winter season, before storing the blade for long-term storage, thoroughly clean it of any remaining snow and dry it. After this, treat all elements with anti-rust agent, and lubricate the rotating mechanisms with oil or grease.

It is important to take care of the condition of the metal surface. It is best to periodically treat it with special chemical solutions that prevent the formation of rust and subsequent destruction of the metal. The surface of the dump can be coated with frost-resistant paint.

Thus, when making a blade for a walk-behind tractor with your own hands from available materials, it is recommended to adhere to the rules and recommendations for its creation. For anyone who decides to assemble a homemade product, it will be easy to determine the dimensions and mount the device to suit their needs and a specific walk-behind tractor model. With such a device, snow removal will turn from hard manual labor into a pleasant pastime.

Original attachments Agat

Working with the attachments of the Agat walk-behind tractor is very convenient and will save you a lot of time, since all products are designed for the most efficient and reliable operation. Thanks to the wide variety of trailed equipment, you can combine many different individual equipment in one copy.

Here is a list of attachments that are attached to the Agat walk-behind tractor:

Plowing cutter
Hilling wheels
Rippers
Weights
Shovel
Vegetable digger
Potato digger
Plow, hiller
Cart.

This walk-behind tractor with attachments can work for a long time.

Let's sum it up

Having carefully studied the diagram and drawings on how to make a blade with your own hands, snow removal with homemade attachments on a Niva or another brand of walk-behind tractor will become simple, easy, and most importantly, an enjoyable experience for you. A snow blade made from scrap materials can last as long as its factory counterparts. The main thing is to adhere to a clear sequence and use only durable and reliable materials.

A homemade shovel for an UAZ or a Niva is easy! By making attachments for a mini tractor with your own hands, you save money from the family budget.