Video to make a protective cover for an angle grinder yourself

Bosch casing for angle grinders with a disc with a diameter of 125 mm. Photo 220Volt

The casing (case, attachment) for an angle grinder performs several functions : it serves as protection for the performer, and acts as an element for collecting dust and other debris. Thus, the cover is an essential part of the grinder when carrying out various types of work. This article is devoted to the independent production of casings. In addition, site visitors may be interested in articles about housings for vacuum cleaners and detailed material about all their types.

Self-production

Making a casing for an angle grinder for a vacuum cleaner with your own hands is not difficult. You just need to approach the problem with imagination. There are many materials for manufacturing:

aluminum pan or plate;
plastic oil canister;
plastic bottle with a volume of 5 liters.

Standard casing

A less expensive manufacturing method is to use a standard protective device. You only need to attach the side cover and pipe to it. To make a side cover, you can take a piece of galvanized steel and then proceed like this:

Cut strips of galvanized steel 15 mm wide and 30 mm long to make corners. Then bend them at a right angle in the middle.
In the side open part of the casing, drill holes with a diameter less than the thickness of the screws. Fasten the previously made corners through these holes.
Cut out the side cover from galvanized steel along the contour.
Drill a hole in it closer to the edge for the pipe.
The pipe can be made by rolling a sheet blank into a pipe. The edges can be secured together with self-tapping screws or clamps.
One edge of the pipe must be cut in several places. And straighten these sectors.
Insert the pipe into the cut-out cover and secure with self-tapping screws.
Also use self-tapping screws to screw the resulting structure to the corners.
Attach the structure to the grinder.
Connection to the vacuum cleaner is made via a corrugated hose. To ensure a secure connection, you must use a clamp.

That's it, the angle grinder with a vacuum cleaner casing is ready for work.

Plastic canister model

After changing the oil or pouring antifreeze into the car, plastic cans always remain in the garage. Thick walls and ebbs in the corners allow it to retain its shape well without deforming. In addition, the size of the canister neck almost matches the size of the vacuum cleaner hose.

Before cutting, you should decide on such a parameter as the immersion depth of the cutting disc. An installed dust extractor will prevent immersion. You can use a standard casing as a basis.

First, mark with a marker.
Use a sharp construction knife to cut holes and cut off unnecessary parts. It is recommended to make holes for mounting on the grinder on both sides. This is necessary in case there is a need to change the direction of rotation.
The hose is connected to the neck using a clamp.
The dust extractor is secured to the angle grinder using a clamp with an adapter ring.
To close an unused mounting hole, you need to cut a circle of a larger diameter and secure it with self-tapping screws.

Tile cutter attachment

Cutting ceramic tiles requires constant supervision. And the exhaust hood for the angle grinder completely blocks the view. To make the casing you need a transparent material.

A 5-liter transparent bottle of bottled water is suitable as a blank. The neck includes the vacuum cleaner pipe. Using a utility knife, cut a hole for the planting.

The bottom of the bottle is cut so that the disc is set to the required height. The structure is secured to the angle grinder with a clamp or screws. The large volume of the bottle does not allow dust to fly away, and the casing simultaneously serves as a dust collector.

Dust extraction from an old saucepan

If sheet steel is available, then it can be used as a basis in the manufacture of a dust extractor for an angle grinder. When carrying out such work, you will need a welding machine. If you don’t have a machine, you can make a nozzle from an old aluminum pan. The principle of making a device from an aluminum pan is as follows:

The basis is taken from a part of the pan with the bottom. The bottom acts as one side of the nozzle, and the other side is made by bending the sides of the pan
It is recommended to use rivets to connect sheet aluminum
A hole of the appropriate diameter is drilled in the wall of the dust collector for fastening to the shaft of the power tool
To secure the hose from an industrial vacuum cleaner, you will need to make a hole on the outside of the side wall to which to attach the neck of a plastic canister, bottle or plastic tube. It can be secured to the aluminum base using threaded connectors with washers
The reliability of the connection between the hose and the nozzle is ensured by a metal clamp

Purpose of the dust collector for angle grinders

Homemade vacuum cleaner: example

Using an angle grinder (grinder) to carry out repair work on concrete at home creates a large amount of dust.

If you need to level a wall, sand it for painting or applying other types of finishing coating, all irregularities or bumps become tiny particles of concrete suspended in the air.

Despite the personal protection used, they penetrate the mouth, eyes, and respiratory organs.

In addition, dust settles on all pieces of furniture, walls, ceilings and other surfaces, requiring labor-intensive and time-consuming cleaning. Dust from brick walls eats into surfaces and irreversibly spoils their appearance.

There are several designs of casings with a pipe for connecting a vacuum cleaner, which significantly improve the process. They are purchased in a store and installed on an angle grinder, connected to a vacuum cleaner. Working with such devices almost completely eliminates the spread of dust and can significantly reduce the pollution of the room and indoor air. Outwardly, they resemble conventional protection, but with a closed housing and an outlet for connecting a vacuum cleaner hose.

Soft starters with three wires

By the way, be careful, there are similar devices, but with three wires.
For example XS-12/D3. Or other models that look similar to KRRQD.

But they are assembled on a slightly different principle and need to be installed after the START button, in the instrument itself. Voltage should be applied to them only at the moment the grinder's start button is closed and immediately disappear after it is released.

The connection diagram for them is as follows:

The phase is supplied to contact “A”, zero to “C”. Next, the phase with the output control wire goes to the engine (this is exactly the third wire).

Without a button, such a device will be constantly powered by 220V, which is not acceptable.

There is no such thing in a two-wire unit, since it is connected to an open circuit, and voltage (potential difference) is applied to it only at the moment of starting and operating the tool.

READ Shavings Got From Grinder What To Do

Another point is the so-called electric brake or brake winding on the crosscuts. It may not work with a 3-wire external soft starter, but it will work with a 2-wire model.

Making a fixture

With dust extraction from the pan

When it is possible to find an old aluminum pan, you can make a dust collector without using a welding machine. The main part of the casing is cut out and fits well to an angle grinder. When performing this work, it is necessary to accurately calculate in advance the maximum penetration depth of the cutting disc, because the height of the cross cut from below directly depends on this.

A seat for mounting on an angle grinder is cut out of another part of the aluminum pan. The hole diameter must be measured directly on the power tool. The size of the dust extractor must be as accurate as possible so that the casing cannot come off due to strong vibration when performing work.

In a similar way, you need to make a pipe for a vacuum cleaner. The protruding edges of the casing should be folded inwards as carefully as possible along a single line to secure the side wall, which can be made from any type of material. For example, a wall can be easily made from thin metal sheet. If there is a desire, then it is worth giving the device a more aesthetic appearance, treating the joints and painting them with enamel.

From a plastic canister

Next, we will consider another economical option for dust removal. In any person’s pantry you can find empty plastic containers for various technical liquids. This container holds its shape well and is quite easy to process. And also such a container has a convenient outlet pipe of the required size.

First, fitting is done, the main purpose of which is to ensure the required immersion depth of the cutting disc. Using a construction knife, cut out the required through holes. Their diameters are chosen in such a way that the homemade structure retains its rigidity. It is worth making special seats on both sides. This will make it possible to change the direction of rotation of the cutting disc.

Next, the vacuum cleaner hose must be connected to the neck of the canister and secured well with a metal clamp. Reliable fastening of the casing to the angle grinder is carried out using an adapter ring and a metal clamp. The assembly of this unit should be approached very responsibly. The second hole must be tightly closed with a lid. When changing the direction of rotation of the cutting disc, the lid is transferred to the other side of the canister.

Such hand-made devices are low cost, but their benefits are very great. A vacuum cleaner complete with an angle grinder will help you perform almost any type of work in rooms with minimal dust emissions. To sand wood, you need a slightly different form of attachment for the grinder. However, it is not very different from the products described above. It can be made in the same ways, using almost any materials.

The simplest method

The first version of a homemade casing does not require large investments, since it uses the one that is already included in the kit. To turn it into a nozzle with a dust extraction you will need:

Cut an exact copy of the factory casing from a metal plate. You can easily find his image on the Internet by entering the marking of your ear.
The next step is to select a pipe that will act as a dust drain. It is worth noting that the size of the pipe must be selected so that the pipe fits tightly into the vacuum cleaner tube, or, conversely, fits tightly onto it.
At the end, you will need to weld the prepared parts, clean them and paint them. That's it, your nozzle is ready.

The advantage of this option is a neat and reliable casing that will look like a factory one, but at the same time your wallet will be satisfied with the cost of such an attachment. The disadvantages include the fact that cannot be adjusted . Also, due to the fairly large distance from the casing to the outer cutting edge of the disk, construction dust and small particles may not be immediately sucked up by the vacuum cleaner through the dust extractor.

Purpose of the casing

The most dusty work is considered to be those performed indoors:

Chipping of concrete and brick. A large amount of dust is generated regardless of the type of material. This work is difficult in that it is often performed with a wall chaser at a height of up to two meters. Dust falling from above settles in a thick layer throughout the enclosed space.
Cutting tiles. This is the most common job for home craftsmen. It is worth noting that ceramic dust is the most penetrating, fine and hazardous to health.
Sanding wood floors. This work is very voluminous and is carried out over a huge area. For this reason, a fairly large amount of sawdust and fine dust is obtained as a result of grinding.

To combat dust formation, manufacturers of angle grinders offer factory-made protection solutions. For example, you can install a small dust collector with a bag on your angle grinder. However, this solution is suitable for large construction teams. This article will tell you what to do for an ordinary home craftsman who will only use an angle grinder.

If your financial situation allows, you can buy a special casing with dust removal from a hardware store or purchase an angle grinder that includes such a device. The high price of such a tool makes the purchase impractical for one-time use, because it is much more profitable to invite a team of builders. But there is another way out of this situation.

You can make an angle grinder with dust protection for a vacuum cleaner with your own hands. You can find many options for this universal dust collector online. Some craftsmen make an exhaust hood from durable metal using a welding machine. But there are simpler solutions to this problem.

You can make a dust collector with your own hands from the following materials:

Aluminum pan;
Plastic containers.

Factory Tile Nozzles

Cutting tiles using an angle grinder with a vacuum cleaner is very difficult, because the cover for removing dust covers the cutting area, and the builder needs absolute control over the process.
But there is a solution to this problem. You need to make a dust collector with your own hands using transparent materials. For example, a large plastic bottle is perfect for this purpose. It is secured using a factory protective casing. Its neck fits well under a vacuum cleaner hose. Using such a transparent device, you can do all types of work by visually monitoring the insertion of the cutting disc into the ceramic tile.

To cut tiles, special diamond-coated cutting discs are used. It is worth noting that the edge of the cutting disc must be solid, because segmented circles increase the likelihood of chipping. It’s also worth setting the grinder to low speed so that the ceramic tiles don’t crack. Experts advise that in order to get an even cut, it must be done in one pass of the disc. If you couldn’t cut it the first time, then you can’t make a second pass.

How to make a casing for a vacuum cleaner with your own hands

An angle grinder with a built-in vacuum cleaner allows you to get rid of small particles of material formed during the cutting process with an angle grinder. But what if there is a need to cut concrete with a conventional tool without additional options? The simplest solution would be to purchase a casing for the vacuum cleaner separately or to make the device yourself. You can hire an assistant who will collect the particles formed during cutting with a vacuum cleaner.

You can easily make a convenient nozzle from a simple plastic canister, in which car “anti-freeze” is often sold. To work, you will need a construction cutter and a container of a suitable size, the neck of which will fit the diameter of the vacuum cleaner hose.

The manufacturing sequence is as follows:

Mounting holes are cut on both sides so that you can easily change the direction of rotation of the disk.
A slot of suitable size is made under the circle.
To attach the grinder cutter, another hole is cut.
The hose is connected to the neck of the canister and secured with an adapter ring with a clamp.
The “grinder” is placed in the casing and all the elements are connected.
The unused hole is covered with a lid.

A good dust collector can be made from a simple five-liter plastic bottle. It is attached using a standard protective casing, and the vacuum cleaner pipe is attached to the neck. This design is suitable for any type of work, with the exception of gating.

Last tip: in order to make a straight cut, markings are first applied. Then wooden blocks are fixed along the line. After this, a shallow incision of up to 1 cm is made, the restraints are removed and work continues. Throughout the entire process, coolant is supplied to the disc blade. All manipulations must be carried out wearing protective glasses, a respirator and gloves.

Canister

If you don’t have welding skills or your wife flatly refuses to give permission to damage the pan, then there is a third option, how to make a protective casing with a dust extractor, which also miraculously connects to the vacuum cleaner tube. What will you need for this?

Find a canister in your garage, closet, or at your neighbor's. Using a construction knife or an ordinary knife, you will need to cut out constructive holes from it, in accordance with the shaft of the grinder and the location of the disk on it. It would be good to remember about safety precautions. Why? Trivial - to preserve the integrity of the hands. Moreover, it is important to choose the right knife. It should have a high-quality handle and fit well in your hand without slipping.

Afterwards, you need to attach the vacuum cleaner tube to the neck of the canister so that it becomes like a nozzle. How? Cut the neck lengthwise and put on a clamp so that you can then tighten the vacuum cleaner tube with it. It is important to remember that in order to achieve good suction of the vacuum cleaner, it is necessary to ensure that all parts of the casing fit snugly against each other.

Popular models

Protective covers for vacuum cleaners for angle grinders are available in a huge range. Moreover, each type can differ not only in design, but also in functionality. Several models of attachments are extremely popular among craftsmen.

Bosch 2605510224. This casing is suitable for angle grinders of various brands with 115 and 125 mm discs. It is equipped with a special ring brush, which allows you to perform work with a fiber attachment and a grinding wheel. The size of the nozzle is 200×190×80 mm, its weight is 0.3 kg. The cost is low.

STOMER 98299441. This device is made in the shape of a semicircle. It is installed on angle grinders with 230 mm discs. The main advantage of the nozzle is the presence of a guide, which is responsible for adjusting the depth of the storm. The casing size is 320x160x240 mm, weight is 2.71 kg. It can also be purchased at an affordable price.
Mechnik Air Duster. This option is suitable for tools with diamond blades with diameters of 125 and 230 mm. It is distinguished by its low price and the ability to connect to medium-power vacuum cleaners (up to 1.6 kW). The casing is lightweight and easy to install.

Blastrak. This is a professional protective cover for a vacuum cleaner that can be attached to sanding tools with 125 and 180 mm discs. The attachment has variable elasticity, is more rigid in the places where it is attached to an angle grinder and is soft at the edges in contact with the floor.
Metabo GED125. This casing deserves special attention. It is recommended to purchase it for processing concrete and stone. The nozzle is equipped with a special pipe that allows you to attach it to a vacuum cleaner.

Algorithm for connecting a vacuum cleaner to an angle grinder

The main principle of instant collection of dust when cutting is based on the creation of a special casing in which debris will accumulate, which will later be pulled out by the vacuum cleaner hose.

The algorithm for how to connect a vacuum cleaner to an angle grinder with your own hands using improvised means provides for the presence of the following materials:

Scotch. It is advisable to take the reinforced version, since it is considered the most reliable and durable. Retraction

This part is used in plumbing work; it is important to use the polypropylene version, it is lightweight and quite durable. The outlet parameters are a bend of 45 degrees and a diameter of 45 mm. Scotch tape used for painting.

It is not at all necessary to use exactly these consumable spare parts; you can replace them with suitable analogues.

Step-by-step process on how to connect a vacuum cleaner to an angle grinder:

Place the tool on a hard, stable surface with the blade facing up

It is important to securely fix the angle grinder to prevent injury during work. Use pliers to secure the outlet at one end, turn on the grinder and carefully cut out a small pipe along its body in the plumbing part. The length of the cut should be approximately 3-4 centimeters. Without removing the plumbing outlet from the disk, you should securely fix it using reinforcing tape

It is important that the winding is tight and tight. You can make a short approach to the grinder disc itself. Next, use masking tape to wrap the entire side of the casing covering the disk. It is important to continue the winding to the tap, connecting both parts.

The last step is to connect the hose from your cleaning appliance directly to the plumbing outlet. You can only use a construction vacuum cleaner; ordinary household models are not suitable. To collect dust while working with an angle grinder, it is enough to turn on the vacuum cleaner, which will draw out the dust that appears during cutting.

Grilling walls with a grinder or the effectiveness of this tool

You can make a channel with a grinder in walls made of materials such as brick, concrete, cinder block, tiles, tiles, and other types of materials. To crush these materials, specialized attachments are used—diamond-coated disks. The process of how to make a groove with a grinder consists of the following steps:

Marking is the most important part of the work, which consists of drawing lines with a marker or pencil on the surface of the wall. To apply markings you will need a pencil, a tape measure, and a rule or water level. When applying markings, you need to make the lines bolder so that when you move the cutting tool, they can be seen. Cutting a groove involves “passing” the tool along the drawn lines. The tool must be held firmly and moved slowly

In this case, it is important to wear special protective equipment, such as goggles, a respirator and gloves. Making a channel - after cutting the lines with a cutting disc, you will need to cut out the remaining concrete. These residues should be removed using a hammer and chisel or a hammer drill.

You can attach two discs to a grinder, just like on a wall chaser. This will allow you to do double the work at once. In one “pass” the tool produces a finished channel. When working to make a neat channel, a large amount of dust is released. To prevent dust from settling in the room where repairs have already been completed, a special attachment is used to which the vacuum cleaner is connected. The vacuum cleaner sucks up all the released dust that occurs during the concrete crushing process.

This is interesting!
In the design of angle grinders, you should use exclusively diamond wheels that are designed for cutting concrete. The use of abrasive and other types of discs is unacceptable. An exception is the use of saw blades with teeth, which can be installed in the spindle of an angle grinder to cut a channel in a wooden wall.

Application of cover for cutting tiles

The manufacturing options for the casings under consideration are suitable for removing dust when processing concrete, brick, cinder block and wood. When cutting tiles, one important condition must be taken into account - the accuracy of the cut. When working, you need to see the mark along which the power tool is guided, thereby making the cut. It is impossible to see the disk through steel or plastic casings, so when using a device for tiles or ceramics, it is important to make it from transparent materials. The easiest option for this is a plastic bottle.

It is not difficult to make a casing from a plastic bottle, and to do this you will need to make one hole in the wall for installation on the shaft, and connect a hose from a vacuum cleaner to the neck. It does not matter for which brand of angle grinder the device is made - Bosch, Interskol, Makita, Diold and others. All tools from different manufacturers have a similar design, so the manufacturing principle is the same for all.

Through the transparent cover you can control the movement of the rotating diamond disk. Moreover, it is recommended to use solid discs for ceramics, since segmented ones contribute to the formation of chips, and as a result the material may be damaged. Moreover, cutting must be done in one pass, otherwise the cut of the tile will turn out uneven. Having made a homemade casing for an angle grinder under a vacuum cleaner, you can test it in action, making sure of the usefulness of such a device.

Wet cutting technology for concrete

The use of water allows you to cut concrete with a grinder without dust and overheating of the tool. The technology allows us to solve several problems at once:

increase the life of the diamond nozzle,
avoid dust formation,
increase work speed.

One way to ensure a continuous flow of water is to secure the hose so that the liquid flows onto the disc. If there is no running water in the work area, you can involve an assistant in the process. He will use a primitive device made from a plastic bottle to wet the circle. At the same time, the incision site is moistened with liquid.

This must be done carefully so that water does not pour into the instrument.

The method is not very applicable in multi-storey buildings, since there is a risk of flooding the neighbors from below.

How to saw with a grinder without dust? Description of 2 reliable methods

When sawing concrete, brick, stone or tile with an angle grinder, a large amount of dust is generated. In this article we will tell you how to saw with a grinder without dust.

Dust not only pollutes a room or work area, but also has a detrimental effect on human health.

In addition, it is much more difficult and inconvenient to work in dust, because... it's hard to breathe and you can't see anything.

To carry out work without dust, you can use two methods.

Self-production

It is not always possible to select a ready-made protective casing for an angle grinder with a dust extraction, since not all products have the same connection dimensions. In addition, they are not always available. The third limiting factor is the price - the Metabo GED125 model will cost 3,800 rubles, and the Bosch GWS 22-230 costs 13,800 rubles, which is 2 times more expensive than the grinder itself. Such prices force angle grinder owners to think about making dust protection themselves, especially since this undertaking is not particularly difficult.

People with a technical mind invent similar devices and remake containers that happen to be at hand for this purpose. As a result, fully functional, albeit unsightly-looking devices appear. They perform their tasks no worse than industrial designs, and cost practically nothing. Let's look at some options:

Homemade casing from a saucepan

Procedure:

you just need to select the diameter in accordance with the size of the disk (2-3 cm larger). The easiest way is to attach the disk to the bottom, choose the optimal position and mark the center with a marker;
then a segment is cut off that determines the amount of protrusion of the disk from the casing;
a circle is drawn around the intended center, the diameter of which corresponds to the seat size of the angle grinder;
A hole is drilled in the marked center, from which beams are cut from the center to the edges using metal scissors. The resulting petals are bent outward, forming a landing diameter for installation on an angle grinder;
a metal clamp of the appropriate size is taken and carefully welded to the bent petals. Try it on the grinder and finally adjust it;
a cutting disk is installed, its position is marked in a circle on the walls of the pan with a margin of about 1 cm. Then transverse cuts are made from the edges to the marked line, and the resulting petals are bent inward. Excess parts are cut off with metal scissors;
the outer wall is attached to the bent petals in any available way - welding, bolts, screwed with wire. The material for it can be metal sheet, plastic, etc.
The hole for the vacuum cleaner pipe is marked in the side of the casing. The pipe itself can be made of a plastic sewer pipe, or made of metal. The pipe is inserted into the hole, attached in an accessible way - by welding, screwed with wire, etc.

A home-made exhaust casing for grinding is made even easier - a pan of the required diameter is installed on the mounting hole, cut to height so that the grinder's grinding disc is completely covered with the remaining part. Then the petals are cut around the perimeter, about 5-10 mm high, and bent outward. A foam rubber seal for doors or windows is attached to them, which ensures the tightness of the casing. All that remains is to make a hole in the bottom next to the landing hole and attach a pipe for the vacuum cleaner. The casing is ready.

Canister device

A plastic canister bottle for technical liquids is convenient because it already has an almost ready-made outlet for a vacuum cleaner. The neck of the canister connects well with the hose; all that remains is to select the desired overhang for the disk and make a hole in the side flat part of the canister. You will need a clamp with an adapter ring that will connect the container to the grinder. This element is important, so it is necessary to make it as carefully as possible, otherwise during operation the dustproof casing will fall off the mounting diameter of the angle grinder. A slot is made in the narrow side part for the disk.

This casing is simple, lightweight and requires little time to manufacture. Old cans are lying around in any garage, finding them is not a problem. All that remains is to spend a little time and labor.

The prices for factory-made protection models are too high, so the vast majority of craftsmen use homemade ones. They do not require any expenses, are made from scrap materials and do their job quite well. It takes only a few hours to make, but the benefits received from such products are great and fully justify the effort and time spent.

How to use an angle grinder: tips and tricks from experts

The manufactured attachment on the grinder not only eliminates the formation of dust, but also acts as an additional protection for humans from the negative effects of power tools. An angle grinder is a life-threatening tool that is used for a variety of tasks. It is important to follow safety precautions when performing these tasks to prevent injury or injury.

Experts recommend following a number of the following recommendations when working with power tools:

Hold the instrument with two hands only
Use only suitable cutting discs and wheels depending on the materials being processed
Do not get carried away with wood processing using an angle grinder. An angle grinder for working with wood is not the best option
Carry out work in protective clothing - goggles, respirator, gloves, etc.
Pause periodically to allow the instrument to cool down.
When using a casing, it is necessary to ensure that it is tightly fixed to the power tool. If it vibrates, it may fall under the rotating disk and be damaged.

To make a homemade casing for an angle grinder to connect a vacuum cleaner, you will need to show a little ingenuity and imagination. Making a device is not at all difficult, and you just need to choose the right material to use as a basis. It can be not only plastic or metal, but also wood, for example, chipboard or fiberboard. And at the same time, you don’t need to buy a homemade device in order to ultimately carry out one-time work on processing concrete, wood or tiles with an angle grinder.

Hi guys! I often send something to you). But that's what happens to newbies. There are a lot of topics - I want to ask a lot, I want to share a lot. In general, this is the topic. When I came across the grinding of fiberglass, I realized that it was trash, to put it mildly. I have an orbital machine with a dust extractor, but I don’t have an angle grinder. And since I rough sand it first, the picture looks something like this:

Peculiarities

A housing for an angle grinder for a vacuum cleaner is a special attachment that allows you to protect the technician from exposure to dust, which flies out from under the disc when working with a grinding tool. Many hardware stores offer respirators for protective purposes, but these devices are ineffective. After a few hours of operation, they begin to clog, which means they cannot cope with their functions. Additionally, respirators are not designed to remove dust from a work area. Therefore, if renovations are being carried out in a residential area that has decorative finishes and furniture, it is necessary to use an angle grinder with a dust extraction.

Most designs of grinders include a dust collector. Thanks to it, dust is immediately collected from under the working surface of the device, without polluting the room. Such models are characterized by high suction power. They protect not only from dust, but also from debris. Additionally, a protective casing made of durable material is installed on the dust removal mechanism. It is able to withstand intense mechanical loads and, during surface treatment, collect different fractions, including small dust particles and pieces of metal or concrete.

The protective casing for a vacuum cleaner performs two main functions.

Dust protection. It prevents the spontaneous spread of debris in the work area. The dust protection element also traps small and large pieces of debris that are formed during surface treatment. In addition, this device protects the tool itself from various particles entering the outer part of the body, which adversely affect the functioning of rotating parts and can subsequently damage them.
Adjustment. The casing is not only responsible for dust removal, but also allows you to adjust the operation of the circle.

Since cleaning is performed with a vacuum cleaner connected to the nozzle, when installing the casing, it is necessary to ensure that the diameter of the dust extraction tube and the opening of the nozzle correspond to each other. The nozzle in the form of a flexible hose must fit exactly into the hole and fit onto the casing without any play.

It is recommended to use a housing for a vacuum cleaner in the following cases:

For grinding concrete and chipping walls and floors. This type of surface treatment produces a lot of dust. In addition, most work is performed at height, and debris falling from above can settle throughout the room. To increase dust protection, you need to choose an aerodynamic or grinding casing that is suitable for powerful models of angle grinders and can withstand loads well.
When cutting tiles. Such work is always accompanied by a large amount of dust, which not only pollutes the room, but is also harmful to human health. For this process, experts recommend choosing a cutting or universal casing.
For sanding wooden floors. This process is quite labor intensive. It involves processing surfaces of large areas, after which a lot of debris and dust are generated. Thanks to the protective casing, scraping takes place quickly and efficiently, since the master does not need to be distracted by cleaning the work area. It is installed on an angle grinder using special fasteners.

The housing for the vacuum cleaner can be sold either complete with the tool or separately. At the same time, many craftsmen make protective devices with their own hands to protect the work process. A homemade casing is no different in functionality from a factory one, but may be slightly inferior in performance. Self-made casings can protect the craftsman from injury by preventing particles of the processed material from flying away. But if financial capabilities allow, then it is better to purchase finished products, as they are of high quality and allow you to expand the capabilities of the device.

How to choose?

Protective attachments play a huge role when working with angle grinders, and special attention should be paid to choosing a casing for the vacuum cleaner. Since not every device can be suitable for an angle grinder and protect the room well from dust, it is important to consider some basic points before purchasing.

To work with concrete surfaces, stone and brick, you need to choose casings with increased protection. Their body must be made of durable material. If desired, protective equipment can be made and connected to the vacuum cleaner yourself, but this will require additional time and experience.
The nozzle must correspond to the dimensions of the nozzle and the modification of the angle grinder. This way the tool can process the material without creating dust.
The choice of casing manufacturer is also important. Today, the market is represented by products of domestic and foreign brands, but not all of them have positive reviews.

It is best to give preference to well-known brands that have proven themselves well among users. In addition, the nozzle should have operating instructions and technical descriptions that will simplify its installation and use.

Nozzles for grinders for grooves

The wall-cutting attachment for the grinder should include:

Installing a second saw blade.
Socket for connecting a vacuum cleaner.
A protective cover to protect workers from construction debris that appears during work.
A seat for fastening the cyclone of a suction vacuum cleaner.

The basic conditions for the functionality of such an attachment are as follows. The grinder must have a sufficiently powerful drive (at least 1500 W), and the length of the shaft on which the main saw blade is installed must be sufficient for mounting an additional disk, with the help of which the second wall of the groove will be formed.

The diameter of the saw blade itself is also important, on which the safety of work and the depth of the cut groove depend.

The type of bearings on which the shaft rotates is also important: the presence of a second disk increases the unevenness of the load, so conventional ball bearings, the permissible axial force on which is small, will fail very quickly, with a corresponding jamming of the shaft and failure of the equipment. A tool with needle or roller bearings is required.

Finally, when the shaft rotates, the movement of the saw blade should be towards the worker, and not away from him (in the latter case, the total torque will push the grinder away from the groove obtained with its help).

A purchased wall chaser attachment for an angle grinder is prepared for work like this. The protective casing is removed from the gearbox. An additional bushing is mounted on the main shaft, which securely compresses the shaft using a clamp fastening.

The first diamond disk of the required diameter is installed on the shaft - from 150 to 230 mm; larger sizes will lead to an increase in the cantilever load on the bushing. It is not recommended to replace the diamond disc with another one, especially if grooves need to be made in concrete. A support washer is placed on the sleeve (usually, professional nozzles come with several such parts of different thicknesses, which determine the width of the groove).

The vacuum cleaner attachment is secured to the dust extraction cone using regular tape. The grinder gearbox is attached to an extended control handle. It should be noted that any wall chaser attachment for an industrial grinder has a seat for a removable handle, which is unified with a standard handle from the same manufacturer of the main tool. This is a limitation of the design under consideration.

After this, check the alignment of both disks, attach the housing to the lever support, set its stroke, and check the reliability of fixation of all elements of the nozzle at idle, and then during the working stroke.

Installation instructions

To improve the performance of the guard, it must be properly aligned and secured. The installation process is simple, even a novice technician can handle it. The nozzle connection looks like this:

First, you should close the standard casing of the angle grinder with an aerodynamic one; to do this, it is rested against the thrust bearing;
then the casing is clamped onto the studs, it is fixed with screws, ensuring symmetry to the disk;
The vacuum cleaner hose is connected to the exhaust pipe; it must pass freely into the opening of the casing;
The installation process ends with a control check of the fasteners, since work can only begin if the casing is securely fixed.

To learn how to make a dust extraction casing for an angle grinder with your own hands, see the following video.

About the Sander Guard

So, a casing for a grinding machine is a kind of equipment that allows you to ensure safety when working on such angle equipment. The operator is freed from constantly monitoring the work process and this makes his work much more efficient. To install such a casing on a grinding machine for protection, you need very reliable and, accordingly, special fastenings.

Such equipment has several functions: protective, and it is this kind of protection that helps to avoid not only human injuries, but also damage to the material itself, for example, any cracks or chips.

Functions of the grinder attachment:

Protection of a person and his life.
Protecting the material from damage.

Usually, when sold, such protective equipment comes complete with an angle grinder. Why can working with a grinding machine be dangerous without life-saving equipment? The thing is that when the work process is underway, all the cutting and grinding discs begin to collapse, turning into small residues.

And then, without stopping the process itself, they also begin to fly in different directions, and their speed is very high and there have been cases when such work with an angle grinder led not only to serious injuries, but also to the death of a person. Therefore, the use of the casing cannot even be in question.

Rules for choosing a casing for a grinding machine

So, when working with stone, concrete or brick, with a casing of poor quality or with little protection, all the dust will fly around the room. And the best thing is, if you are going to connect a sander with a vacuum cleaner, then make such protective equipment yourself.

If you decide to purchase a casing in a store, and not make it yourself, then you must understand that there can be a huge number of models of such products and therefore it is worth familiarizing yourself with them in advance, so that later you do not waste your time looking at unfamiliar and incomprehensible ones technical descriptions for each equipment.

Complicated method

The second option will require an iron or aluminum pan. All actions take place in stages and do not require special skills in making additional equipment for the ushma. However, some tools are worth buying in order to do everything as accurately and efficiently as possible. And I wouldn’t want a hand-made protective element to cause injury.

Cutting out the shape for the angle grinder casing according to pre-measured dimensions. It is important to remember the saying: measure seven times and cut once. Why? It is unlikely that the spouse will be happy if, in order to save on equipment for ushma, she has to spend money and buy a lot of new dishes.
From the remains of the pan, teeth are cut to the size of the grinder's torque sleeve. It is tightly secured to the grinder with a special clamp purchased in advance from the store.
A cone is made from the same pan according to the size of the vacuum cleaner tube so that it can be tightly attached to the shape of the casing. It is worth recognizing that this may require considerable effort.
It is necessary to cut a plate that exactly follows the shape of the future casing. And, accordingly, connect all the parts into one design.

The advantages of a casing made from a saucepan include the fact that there is no need to spend a lot, and you also do not need to have special welding skills. The negative aspects of this option include the scrupulousness of assembling the entire structure and, again, the inability to adjust the depth of the cutter.

Causes of dust formation

The grinder is a universal tool. With its help, using various attachments, you can cut metal, stone, porcelain stoneware and tiles, process wood and other materials. But one of the disadvantages is the formation of a huge amount of dust.

Work that causes the formation of large amounts of small debris:

Grooving grooves on walls. The work is carried out using plaster, and cement and sand have a fine fraction. The height of the passage of the channels is at the level of one and a half or two meters. From such a height, dust settles evenly over the entire area of the room.
Sanding of wooden structures. Before painting or varnishing, wooden products must be removed from the cellulose fibers that form during the sawing process. Cellulose is thin, light and hangs in the air for a long time.
Removing old paintwork. Before applying fresh paint, the old paint must be removed. A flap sanding wheel is used. The paint it removes is fine.
Cutting floor and decorative ceramic tiles. Sintered ceramic has a fine grain structure and it penetrates everywhere.
Sanding parquet or wooden floors. Floor leveling occurs by removing the top layer. The irregularities have different heights and therefore, in addition to shavings, a lot of wood dust is formed.

Upon completion of the repair, dust must be removed from all possible cracks and cavities. To protect adjacent rooms from construction dust, protective screens made of polyethylene film or light fabric are installed in doorways. Special devices are also used that you can make yourself.

Types of covers for grinders

Plastic casing for angle grinder (125 mm) MESSER. Photo VseInstruments.ru

There are several types of covers for angle grinders:

attachments for vacuum cleaners are used when chipping walls, sanding surfaces and performing other work during which a large amount of dust, particles and other debris is formed;
covers designed for grinders with different disc diameters;
nozzles made of metal and plastic;
with and without fastening;
with slides - special guides;
various brands: Russian and foreign.