DIY power saw at home

A circular saw is useful, and sometimes simply necessary, for the home craftsman. Owners of private or country houses are constantly repairing, creating, rebuilding something. The main material is wood or its derivatives - plywood or chipboard, which must be cut, cut into blanks or parts.

Purchasing a hand-held circular saw requires expense, and creating a stationary circular saw with your own hands is impossible without a working shaft and an electric motor. A good way out would be to use a grinder as a drive mechanism, which is equipped with a seat for a saw blade and has its own electric motor. All you need to do is create external equipment that turns a conventional angle grinder into a type of circular saw.

Homemade devices

Making a circular saw is not that difficult; problems may arise when fitting the components.
Choosing all the elements correctly so that they work flawlessly is an important task. The shaft must have self-adjusting bearings if the unit is used daily. It is best to select the bearings themselves with two rows of balls, which will be adjusted using a clamping nut. The working surface must have a “grid” marking. Without this coordinate system, accurate woodworking is quite difficult. The protective casing must not be neglected - during operation it reliably protects the device from mechanical damage. A circular saw operates in different modes when working with different materials, so it is advisable to have a device that controls such a process. Several grooves should be made on the shaft so that it is possible to rearrange the pulleys, thus changing the speed.

When you have to saw bars or make several cuts from different directions, you need a stop that has a “P” configuration. At its base lies a board 30 mm thick. Sidewalls 12 mm thick are screwed to the base. Thus, the emphasis is installed on a beam, the size of which from the cutting point corresponds to the size of the cutting disc. On both sides it is pressed against the beam with clamps. If the beam is too massive, then it is rearranged and another cut is made.

There is also an edge stop that is in demand. To make it requires a lot of time and good qualifications of the craftsman. Be sure to make a diagram before starting work. This stop is made from plywood (20 mm), and the stop strip is also made from this material. Manufacturing phases:

longitudinal grooves for keys are cut;
the keys are mounted on a thrust strip;
Another groove is cut between the grooves made to secure the thrust strip;
another hole is made in the base, its size corresponds to the saw blade of a circular saw;

Sidewalls-limiters are mounted, and there must be clamps in order to securely fasten them. To place the emphasis on the workpiece, the bar moves in the grooves and is fixed through the slot with clamps. It is best to immediately attach a ruler or tape measure to the frame - this makes the work much easier. The pusher is convenient for working with small workpieces - it allows you to fasten the part on both sides, which ensures precision in work

It is also important to do:

elevator;
riving knife;
lifting mechanism.

Capacitors are calculated according to the following scheme: per 1000 watts there are 100 uF for a working type capacitor. The capacity of the starting capacitor must be ordered twice as large. It should be remembered that the SB starting block is a device that automatically returns to its original position. This is very convenient, since literally a few seconds after the start you can begin the workflow.

Table saw

Sometimes there is a need to change the width of the board or the thickness of the block. The best option for such work is a circular saw, especially if there are a lot of boards. For cutting boards of short length (1-2 m), a tabletop version of a circular saw is very useful. It is not necessary to buy such a machine; you can make it yourself from the same grinder.

The design of a circular saw is much more complex than a miter saw. The contact time of the saw blade with the wood is quite long, therefore the reliability of attaching the grinder body to the frame should be higher.

This is what one of the options for a tabletop circular might look like.

The photo shows that the desktop consists of two planes:

the upper table is designed to advance the workpiece;
The lower one serves as a stop for the sander.

The disc passes through a groove in the top surface. If the angle of contact of the two planes is provided with rotary hinges, then it will be possible to adjust the working height of the saw blade to reduce the area of rubbing surfaces.

The head of the bolt with which the angle grinder is secured is clearly visible on the top surface of the table. The protruding bolt limits the width of the board being processed. You can cope with this problem by laying another layer of plywood.

Turning the angle grinder on and off using the key on the body is quite inconvenient. If the key can be fixed in the working position, then it is worth installing a socket with a switch on the outside of the machine.

The stop angle must have the maximum possible length to prevent the board from deviating from the cutting direction. It is better to fasten the corner in such a way that you can change the working distance between it and the disk: then the width of the cut part will also change.

Security measures

When repairing an instrument, we must not forget about safety measures. First of all, you need to disconnect it from the power supply and do not plug it into the network until final assembly.

It is recommended to wear gloves when working with the chain and bar; this will protect your hands from cuts. When disassembling screw connections, if the screw cannot be unscrewed, you need to stop making efforts and use an aerosol lubricant like WD-40; this will relieve the tension and after a few minutes you can simply unscrew the screw.

It is also worth remembering about electrical safety; you can repair parts of electrical equipment by using only the nominal value of the parts that were originally installed.

It is optimal to use machine chain sharpening. But if it is not possible to use an electric machine, then you can also use the manual sharpening method using a special file and a guide jig.

The chain is put on the bar and secured in the saw. After this, the chain is tensioned. After it is tensioned, sharpening is done:

As you can see, the process of repairing an electric chain saw does not pose a big problem and is quite feasible even for those who have never repaired power tools. Another thing is that before you start disassembling, you need to carefully study the structure of the tool and imagine all the operations that will need to be performed during repair.

Source

What characteristics should you choose based on?

All models, even of the same brand, differ from each other in both significant and minor details. Below are the main qualities, the most important first. Then in descending order.

Engine power and location

The more powerful the engine, the easier the electric saw cuts the material. If two models have tires 40 cm long, but engines are 1.2 kW and 2.2 kW, both are capable of sawing a stack 35 cm long. But the more powerful one will do this easier, faster, without overheating and overload, which means it will last longer.

Therefore, when choosing, you should choose the option that is suitable for the upcoming work. There is no point in sawing medium-sized workpieces with a heavy tool. Medium power chain saws are the most versatile.

Power type

Comparisons of corded and cordless electric saws are given above. Battery-powered options are chosen without hesitation when you need to work far from electrical outlets, at heights, or in hard-to-reach places.

This includes pruning the garden, preparing firewood for a fire in the forest, and construction work, especially at heights. That is, wherever there is no network electricity nearby or the wire will seriously complicate work.

Due to the weakness of the engine, the saw set on such a tool must always be in good condition. If with a powerful engine you can saw with a slightly dull chain, deformation and slight jamming of the chain in the tire groove, then the battery version will lose a significant part of the power and capabilities.

Kerf dimensions

What diameter of a log, or how wide a stack can be sawed in one pass, depends on the length of the bar and chain (saw set). A 25 cm long tire is capable of sawing a log with a diameter of 20-24 cm and a stack of the same width. Why not 25 cm - it’s better if the tip of the bar extends outward, so sawdust is easier to remove from the cut.

In this case, the height of the stack can be any. Therefore, the depth of cut for such a tool is not limited.

Availability of oil tank and its capacity

The chain requires lubrication during operation. That's why all models have an oil tank. The volume of the oil tank is specified in the operating instructions for each model (approximately from 100 to 180 ml). The larger it is, the less often you have to fill in oil.

An enlarged tank increases the size and weight of the tool. Taking into account the fact that the sizes of the tanks differ slightly, this parameter is of little importance when choosing.

Power cord

In many cases, work is carried out at a distance from the outlet. Therefore, you have to use an extension cord. The longer the wire of the saw itself, the more often an extension cord is not required. A wire 1.5-2 m long can be considered an advantage. But it turns into a disadvantage when storing and transporting the instrument.

It is easier to put a power saw with a short cord of 30-50 cm in a box on a shelf. No need to wind and unwind the cord. Long extension cords are wound on a drum or left permanently in place, making them easier to handle. There is no point in installing a drum under the cord on a hand-held instrument (dimensions, weight). That's why most models have short power cords.

List of equipment characteristics

Small miter saw
The next stage of work is to calculate the characteristics that a miter machine should have for processing wooden boards. They depend on the size of the workpiece, its configuration and the requirements for the quality of facing.

Initially, the required cutting depth and processing speed are determined. To perform the trimming operation, it is enough to purchase or make a desktop model. Large production machines may have multiple sawing units and a number of other additional features.

But regardless of the design features, the cross-cutting machine is characterized by the following technical parameters:

maximum and minimum saw diameter. It determines the cutting depth and dimensions of future equipment;
range of distances from the end plane of the saw blade to the work table
parameters of the rotary block, if provided in the design;
power of the main drive electric motor;
number of revolutions and the possibility of their adjustment.

To connect the chip vacuum cleaner, you need to know the diameter of the supply pipe. If it has a non-standard size, you can use adapters. Also, additional components - clamps - are used to securely fix the boards. Their design and configuration directly depend on the parameters of the workpiece.

Basic malfunctions of electric saws

Electric chain saw breakdowns do not occur out of nowhere. Most often, they can appear due to power surges in the network, improper operation of the unit, or poor build quality of the device. The main malfunctions of electric chain saws include the following.

When I press the start button on the unit, the saw does not start. The network cable or power plug of the device may have failed. If everything is in order with the cable, then the cause of unit failure may be a faulty start button, burnout of the motor windings, or complete wear of the brushes.
During operation, the brushes on the electric saw burn, and a circular fire appears on the motor commutator. The malfunction may be caused by worn brushes or a short circuit in the armature winding.
The chain is not receiving lubrication. This happens if the oil in the tank runs out, the tube or hole responsible for supplying lubricant is clogged, or the oil pump fails.
The unit cannot develop full power. Possible reasons are as follows: the brushes are worn out; interturn short circuit or break in the armature winding; low voltage in the network; the start button is faulty; jamming occurred in the gearbox; brake system malfunction.
The power saw motor stops during operation. This behavior of the unit may be caused by gearbox jamming or brush wear.
The electric motor of the device quickly overheats. There may be several reasons why the saw heats up: high ambient temperature; poor engine ventilation when operating at low speeds; ventilation holes are blocked or clogged; long-term operation of the unit under heavy load; increased rate of operation of the device without rest breaks; gearbox malfunction; lack of lubrication; damage to the motor windings.
The unit makes an uneven cut. This may be due to dull chain cutters or uneven tire wear.
When the motor is running, the chain remains motionless. Most often, breakdown occurs due to clutch failure. Also, this malfunction can occur if the gears of the gearbox and drive sprocket break.

Types of frame units

It is recommended to pay attention to a sawmill made from an electric saw, in which the frame is the base. Typical factory-produced products are expensive and are considered professional equipment with rich functionality and a high level of performance.

The finished tool will be able to pay for itself after a few months. It is necessary when there is a large volume of forest. In other cases, it is advisable to purchase or make your own sawmill from a small electric saw.

Equipment designed for sawing wood is presented in a wide range. Most of them are too expensive for a typical country farm, and processing volumes are aimed at the scale of industrial enterprises and reach several thousand cubic meters per day. Experts distinguish 3 types of such devices:

disk;
tape;
tire

Circular saws are the most common on the farm. Among their disadvantages are the increased volume of waste compared to tape counterparts and the high cost of high-quality discs. Electric band saws are recognized as one of the most profitable options. They are weather tolerant and produce little waste. It is recommended to use them with wood whose diameter does not exceed 70 mm. The design of the device complicates the process of reproducing it yourself.

Tire sawmills are in great demand among hobbyists. They are capable of processing large volumes of wood. A do-it-yourself tire sawmill can be made more easily and quickly compared to analogues.

Specifications

Factory-produced devices have their own characteristics that affect the price. Electric saw PCM-1E (380 V) has small dimensions and copes well with processing wood with a diameter of no more than 60 cm and a length of no more than 9.5 m. It is equipped with a three-phase electric motor, the power of which reaches 5.5-7.5 kW.

The small-sized PCM-3B (Stihl MS 660) equipment is capable of processing logs with a diameter of up to 60 cm and a length of up to 9 m. The professional model has an engine power of up to 5.2 kW. The unit can process 6 cubic meters of wood during an 8-hour shift.

The Taiga DP-1 disc sawmill easily processes wood with a diameter of no more than 90 cm and a length of up to 7 m. It is capable of producing several types of wood products and is equipped with an 11 kW electric motor. Produces up to 10 cubic meters of wood per 8-hour shift. The Wood-Mizer LT-15 band sawmill processes wood with a diameter of up to 70 cm, the length of the logs is not limited, and the weight can reach 2 tons. It is presented in two configurations - with an electric motor with a power of 11 kW and a gasoline engine with a power of 18 hp.

Opinions about saws based on two-phase motors

A cross-cutting machine with a broach for wood using a two-phase motor can work for a very long time. In this case, the level of overheating depends on the type of ventilation ducts. Modern modifications stand out for their portability. It is also worth noting that there are many devices with multiple ventilation ducts. Models with two handles are in great demand. Model rotors are used both with and without regulators.

A good homemade wood trimmer has a frequency of 1700 rpm. Not all modifications are suitable for cutting boards. You also need to remember that models with throttle valves are very expensive in stores. Most devices are made with manual starters. However, there are models with electronic analogues that are made specifically for professional builders.

Homemade electric saw from a grinder

Some craftsmen decide to convert standard equipment into what they believe is more functional.

DIY circular saw from an angle grinder

To convert an angle grinder into a circular saw, you will need a saw blade, bolt ties, a gearbox, a metal angle, steel rods, metal clamps, and a set of tools. Before assembling the device, it is advisable to make drawings and calculate the gear ratio taking into account the parameters of the gear disk.

The grinder's engine will become the power plant for the created circular saw. First, remove the disc from the angle grinder. The new toothed disk is tightened with a metal corner. The body of the angle grinder itself is covered with clamps, and from below - with a double strong metal tape.

Next, a hole is made in the gearbox to install the handle mount and grooves for the bolts are drilled in four places. The metal rods are shaped into 6 cm loops, then the handle is attached to the body along with the electric motor. Sometimes such a saw is installed on a base made of plywood or chipboard to create a stationary circular saw.

Trimming from various scrap metals

This is a fairly heavy crosscut on a stationary metal table. It will take some effort to control it. But in the end, the saw mechanism moves smoothly, without jerking, and trimming with your own hands is easy.

electric motor power - 2.2 kW;
disk revolutions - 2800;
cutting depth 80 mm.

Materials and tools required for assembly:

900 W electric motor;
a metal sheet;
metal corner;
channel;
hinge group;
powerful spring;
Bulgarian;
welding machine;
file.

The bed is made from adjustable supports, a metal corner and posts from an old bed. The working surface is a metal sheet like a table surface, in which we cut a hole, and process the edges with our own hands using a file.

The pendulum stand for the saw is welded from a channel mounted on a sheet of metal; its height is about 80 cm.
The stand for the electric motor is made in the form of a movable metal plate mounted on hinges. When installing an electric motor, a spring is used as a stabilizer. Then you can do without a pendulum and belts.
The tension belts are adjusted with a conventional hinged bolt, and the pendulum for the mechanism is also made of metal.
As an operating tool, a disk with a diameter of 420 mm is installed on the trimmer.

What can be made from an electric saw

Since sawing logs into bars and boards always requires cutting equipment, factory sawmills use rack (band) and circular saws. Naturally, for the construction of a small house or the production of several cubes of boards, it is impractical and expensive to purchase such a machine. The best alternative may be a homemade design based on an electric chain saw.

Its potential is quite enough to satisfy the small needs of private developers, and just ordinary home craftsmen who cannot afford ready-made lumber. The electric saw here is the main device, combining a universal mechanical feed of the cutting tool and an electric drive. A chain sawmill, unlike a circular saw, is best suited for longitudinal bucking and sawing logs, as it has:

rough cut sufficient for efficient sawdust ejection;
capaciously arranged electromechanical feed of the cutting tool (chain);
relatively low cost.

Important points when constructing a pendulum machine

The type of tool under consideration belongs to the category of dangerous, therefore, when constructing the equipment, the following main points are taken into account:

The manufacture of the frame is the basis responsible for the reliability of the installation. It is impossible to save on the manufacture of the frame, therefore, exclusively steel materials are used, the thickness of which is at least 2 mm. Frame - the design of this part can be different, but the most important thing is to ensure the mobility of the cutting tool. This is achieved through the use of different materials, but in any case, you need to think carefully about the quality of the hinge joint, since your life depends on it. It is better to spend more material, but make a high-quality and safe cutting machine. Tool fastening - the angle grinder is fixed directly to the moving part. Moreover, the fixation must be as reliable and high-quality as possible. When using an angle grinder, “reverse impacts” may occur, which are dangerous because the machine may simply be damaged, and the master who performs the manipulation will suffer as a result. Provide a counterweight - this is a small but important element that allows the tool to return to its original position when not needed

This will eliminate the possibility of damage to parts of the human body. A protective casing - it must be required, and it does not matter what design of the machine is invented, but using the device without a protective casing is strictly contraindicated. The presence of a ruler - this will improve the accuracy of the work performed, which is important when cutting such parts, like tiles, ceramics, and also metal. A starter is also a kind of device that affects safety. The control button should be located in close proximity to the master performing the work. This will allow you to quickly react at the right time by turning off the power supply to the tool.

This will allow you to quickly react at the right time by turning off the power supply to the tool.

In addition to options when the machine has a moving part, there are also methods for manufacturing cutting devices with the tool located in the lower part of the bed or workbench tabletop. However, this option is suitable only for cases when sawing wood is planned. Below is an example of how to make a home sawmill from a grinder quickly and easily. Details on making home sawmills can be found in this article.

This is interesting! The tool can only be used in this form with disks or circles for processing wood. Cutting tiles and metal in this position of the grinder is extremely dangerous.

How to sharpen a chain yourself

Working with a properly sharpened tool makes it possible to significantly extend its service life. Regardless of the type of chain, sharpening is the main operation to maintain the chain in good condition.

It is optimal to use machine chain sharpening. But if it is not possible to use an electric machine, then you can also use the manual sharpening method using a special file and a guide jig.

The chain is put on the bar and secured in the saw. After this, the chain is tensioned. After it is tensioned, sharpening is done:

At an angle of 90 degrees to the bar in a horizontal plane, a jig with a file is installed in the cutout of the cutting tooth.
After this, a tilt is made in the vertical plane so that the file follows the direction of the previous sharpening.
The metal is removed using 2-3 movements with force.
The jig is removed and moved to the next tooth on this side of the sharpening.
Having finished setting the edge on one side, the file and jig are moved to the other side, and the process is repeated.

Transferring the body with the saw to the base

The next step is to transfer the entire structure to the main frame, which has the shape of a parallelepiped. This frame is installed on rollers that will move along the rails and cut the log. The sides are a welded frame made of thick metal. They are fastened together at the top. In other words, the front view will resemble the letter P mounted on rails.

The distance between the side posts is 1-1.5 meters and is calculated based on the length of the tire: it should be slightly larger. The side posts themselves are so wide that a structure with a cutting base can be installed inside. If this structure is 60 cm wide, then the width of the side edges should be the same. This is done with the expectation that a saw will be installed inside one of the racks. The axis along which it moves is attached at the top and bottom inside the side frame.

Thus, vertical movement is ensured by the axis. Horizontal movement occurs using rollers that roll on rails.

DIY circular table (with drawings)

This section offers a model of a universal table on which you can place a circular saw of any technical specifications and dimensions. To make the structure you will need the following materials:

a sheet of plywood, preferably with a laminated top covering, at least 10 mm thick and 800x800 mm in size;
4 laminated chipboard sheets 16 mm thick (400x784 mm);
bars 50x50 mm;
bolts and screws.

To make a homemade circular saw and table, you will need drawings

Making a table for a circular table can be done in the following sequence:

The upper part of the future table is assembled from laminated chipboard sheets, which is a box without a bottom. The sides are attached to each other using bars, the length of which is significantly greater than the height of the sheets.
The manufactured structure is turned over, the bars-legs of the future table in the lower part are fastened with additional jumpers.
A tabletop is cut out of plywood, in which a longitudinal hole is made using a jigsaw - a saw blade will be inserted into it.

It’s easy to find a drawing of a similar design on the Internet, which will greatly simplify production. You can modernize the version of the circular table proposed above with your own hands by replacing the bars with a metal corner or making a so-called box from boards. It’s a good idea to make a shelf at the bottom of the structure.

Making a crosscut from a circular saw with your own hands

Laying a wooden floor, replacing platbands, covering the facade with plank, clapboard, and creating landscape design elements require a dimensional board. The process of preparing such a board is called trimming. That is, the ends of the material are cut off in order to obtain the desired size of the workpiece and make the cuts aesthetically pleasing.

Do-it-yourself trimming makes work faster and more economical

To make a crosscut from a manual circular saw with your own hands, you will need available materials and used tools. The standard characteristics that a future trim should have are:

maximum cutting length – 350 mm;
optimal engine speed – 4500 rpm;
light weight.

The upper part of the power tool is attached to the kingpin using a large bearing - 150 mm (it is not difficult to purchase on the market.) Ears are attached to the outside of the bearing. They are used to fasten the tool to the surface of the frame using M6 screws.

The main devices for making a circular saw with your own hands are car shock absorbers (they are convenient to use as a broach), a soft start button and additional protection that is attached to the power tool and the bed.

The upper part of the crosscut is attached to the kingpin using a bearing

Important! Before assembling the structure, the shock absorbers must be disassembled, the oil drained and air holes made.

The advantages of a homemade miter saw include the following:

The design is easy to disassemble, and the power tool can be used for its intended purpose.
Low cost. Without taking into account the price of the instrument (used), the costs will be no more than 500 rubles.

Among the significant disadvantages, it is worth highlighting the high noise level. It is almost impossible to eliminate this drawback. In addition, it is necessary to make a test cut (selecting and fixing the draft) to ensure good quality of subsequent work.

Making a miter saw

A miter saw is a circular saw with guides, i.e. tire. The latter is attached to the platform and allows the saw to cut complex shapes from wood.

Therefore, the question of how to make a miter saw is always relevant. It is solved in the following way:

A chipboard bridge-stand for guides is made from wood;
A slot is made in the blade of the stand for the saw, and tires are attached to the sides;
A circular saw is inserted between the tires;
The platform is attached to a chipboard semicircle, which serves as a clamp and regulator of the position of the workpieces.

Now the hand tool can move smoothly along one axis, which makes high-quality and unique cuts possible.

Nuances of use

A saw, even a homemade one, can cut types of materials such as:

Plastic.
Wood.
Aluminum.
Non-ferrous metals and alloys.

The maximum weight of the product is 28 kg, which is due to its characteristics. This type makes it possible to make miter joints; they are common in framing and furniture workshops.

The price of a tool that rotates 360 degrees is much higher. Its tilt is easy to adjust. However, know that in order to figure out what angle is required, we need to decide what materials we will use.

A miter saw is created with your own hands on the basis of existing equipment - a hand-held circular saw, an angle grinder (grinder). And when installing disks of a specific type, a homemade device can be used to cut profiles on a metal-plastic base, pipes, which will increase the area of its use.

Homemade sawmills from electric saws: design options

Among all the variety of homemade products made from electric saws, sawmills are the most popular and widespread product that craftsmen have been producing for many years. Factory analogues of such devices are quite expensive due to their high performance. They are capable of processing thousands of cubic meters of timber per day of operation.

When there is neither such a scale of woodworking nor finances, you can pay attention to one of 3 types of homemade sawmills:

tape; They have a complex design, but are adapted to any working conditions.
disk; Quite easy to assemble, but not reliable, which is why they are in demand among amateurs. Circular sawmills based on electric saws are quite common in everyday life, productive and versatile in the tasks they perform;
chain

In view of this, we will dwell in detail on their manufacturing technology.

How to choose a grinder to create a circular saw

Any professional equipment can be used. However, it is worth noting that the more powerful the grinder, the more productive the sawing unit will be. If you use angle grinders with low power, then the future structure will only be able to work with chipboard and any thin sheets.

The only thing that is important to pay attention to is the characteristics of the short-term operation of the unit. If the design becomes hot, the engine will soon become unusable.

If there is a need to systematically use the structure, you need to purchase an angle grinder of suitable power (at least 1600 W).

Main stages of work

First of all, we cut out the housing to which the electric motor will be attached. Then, on a lathe, we turn a steel pulley onto the engine drive shaft. To make a homemade cordless electric saw, you will need a small tire and a piece of chain of suitable length.

Then you need to make a wooden handle, in which you will need to drill a hole and install a power on/off button.

At the next stage, we make a whole 24V battery pack from 18650 batteries. We weld the contact plates using resistance welding. A full battery charge will last for one hour of continuous operation of the electric saw.

It is necessary to make a stop handle from a piece of round steel pipe to make sawing more convenient. Then we begin assembling the entire structure. The result is a compact electric saw that runs on a battery.

When working at home, you should always be able to make a tool with your own hands. A homemade circular saw will perform its duties no worse than its factory counterpart, and its maintenance and dismantling will be much easier. In special cases, a circular saw can be converted into a radial or grinder, which has its own very pleasant moments.

You can make a circular saw yourself; for this you need to have good drawings and tools.

Option 2 - how to quickly and easily make a pendulum saw

If you have a welding machine and consumables, you can make a stationary machine from an angle grinder in a matter of hours. Moreover, you don’t need to buy anything for this, since the necessary tubes, fittings and profiles can be found in a garage or a pile of scrap metal. To build a simple cutting machine using an angle grinder as the main tool, you will need to use the following parts:

Metal profiles measuring 150-200 mm
Sleeve 10-15 cm long
Hairpin 20 cm long and 8-10 mm in diameter
Washers
Metal corner
A sheet of metal 2-3 mm thick, which will act as a base

So, to make a simple homemade product you will need to perform the following steps:

Cut the stud to the required length, then place the sleeve inside (it should move freely along the stud), and tighten the nuts onto the ends of the protruding stud. Tighten two nuts on both sides, since the second will act as a locknut. The nuts should not be screwed in completely, they should not come into contact with the sleeve. The resulting structure should be welded to a steel sheet

In this case, it is important to grab the nuts, and the sleeve must remain mobile, that is, move freely. At the next stage, it is necessary to make fastenings for the angle grinder. To do this, you will need metal profiles, as well as washers that will play the role of brackets. Cut to the required length (it all depends on the tool used, but for a low-power angle grinder, the profile length is 15-20 cm)

Weld washers to the ends of the profiles. It is recommended to use at least 2 mounts for an angle grinder, but three are better. The angle grinder has threaded holes for connecting the handle. We use these holes to attach the tool to the movable base using pre-prepared brackets. First, the brackets are attached to the tool using bolted connections of the appropriate size, and then the reverse ends of the profiles are welded to the sleeve. As a result, we get a ready-made machine that can be produced literally within an hour

The photo below shows the design of a homemade machine made from a grinder with a detailed description of the necessary materials. Using the instructions, and for some, a diagram is enough to make a homemade cutting machine

It is important to take into account that a casing for an angle grinder must be provided, otherwise the risk of serious injury increases. It is strictly prohibited to operate the tool without protective clothing, not only on a person, but also on the device itself.

The simplest device is ready for use. The angle in the machine design is used as a guide for centering cutting materials. You also need to make a straight hole in the iron sheet, into which part of the disk will “go” when sawing workpieces.

Disk speed and security

Without ensuring high speed of the toothed disk, it is impossible to guarantee the quality of the cut. However, for homemade equipment operated in a home workshop, safety during operation is no less important.

It is necessary to provide protective devices that are traditionally equipped with industrial designs. The opinion that one can completely do without such protection at home does not stand up to criticism.

TB rules are “written in blood.” All it takes is one awkward move to end up on the surgeon's table.

Therefore, security should be given the utmost attention

What can be made from an electric saw

rough cut sufficient for efficient sawdust ejection;
capaciously arranged electromechanical feed of the cutting tool (chain);
relatively low cost.

What can you make yourself?

The main difficulty faced by anyone who wants to make a hedge trimmer on their own is the manufacture of serrated knives, which must move close to each other, with the permissible gap between them being hundredths of a millimeter . Moreover, the knives should fit tightly to each other everywhere, including where the teeth pass each other.

Due to such high requirements, non-compliance with which leads to a severe deterioration in the operation of the cutting mechanism, homemade workers take two paths:

use a ready-made cutting mechanism from a brush cutter with a burnt out or broken motor;
They develop their own cutting tool designs for less stringent requirements, albeit with noticeably worse cut quality.

The advantage of a ready-made cutting tool, especially premium brands and expensive models, is that it is made of the highest quality, so it cuts the bushes evenly and accurately.

And using an angle grinder (angle grinder) or a chainsaw instead of a standard motor allows you to restore the functionality of the tool without purchasing a new engine, which is the most expensive component of a brush cutter.

The advantage of a self-made cutting tool is that its construction does not require a faulty brush cutter, so even those who do not have spare parts from a serial device lying around in their pantry can use this method.

The noticeably worse quality of cutting the green fence is not a problem for such DIYers, because otherwise they would buy an inexpensive Chinese device and use it as is, or attach it to a grinder/chainsaw.

The most effective cutting tools that you can make in your garage or workshop are:

chain saw with comb;
attachment made from parts from an old hedge trimmer.

Working with a saw and grinder

Tools and materials:

grinder 150-180 mm;
drill;
self-tapping screws;
steel clamps;
sheet steel;
pliers.

Circular saw diagram.

Before you make a circular saw yourself, you need to try making it from other tools. Most often, the process is organized with the help of an angle grinder, because it can be remade much faster and easier than any other analogues.

The simplest option best damages the instrument. To do this, you will need to screw the tool to the base using metal screws. If desired, you can make through holes with a drill and tighten them with bolts and nuts, which will be much more reliable in operation, because the tool will no longer strip the thread in case of strong tension. The only nuance that should be taken into account is the factory imbalance of the tool, due to which you will have to fix it very carefully so that there is not even a small chance of movement.

If desired, you can complicate this design, and this will also protect the instrument from unnecessary interventions inside. For fastening you will need steel clamps that wrap around the tool at 3-4 points and then secure it with bolts on both sides.

This design is very reliable, but special attention should be paid to the quality of fixation in order to avoid even small misunderstandings

Diagram of a station for a circular saw.

For those cases where the tool is made stationary, you can use more powerful options for angle grinders. The angle grinder itself is attached to the reduction gearbox using bolts or self-tapping screws (depending on the ability to make a joint without damaging the tool, because sometimes the mounting locations do not match), after which they are installed together on the table top and screwed in the highest quality way.

The most reliable method will also be the most difficult, because it will require the support of a turner-miller. His task is only to carve a special part that would be suitable in its parameters for coupling the grinder and the tabletop. This coupling method is the most reliable; moreover, even microscopic movements are excluded, which is not possible to achieve in every factory tool.

One should take into account the fact that in any case the protective casing is removed, and instead a homemade one is made from sheet steel. It will no longer be possible to use the mount for the casing due to the fact that it is used for coupling, and the homemade product should be mounted directly to the tabletop. To make it, you need to cut a semicircle from sheet steel, the end of which is bent and clamped with pliers. This design will withstand any surprises after it can be screwed on.

When choosing an angle grinder, you need to be extremely careful so that the number of revolutions is small and the power is high. If the speed exceeds 4500 rpm, you will have to use reduction gears, because otherwise, the cutters will grind down very quickly.

It is very important to remember that under no circumstances should a circular saw made from an angle grinder be remade back, because for this reason, every day in all parts of the world people end up in hospitals with injuries of varying severity

Even if an angle grinder is urgently needed, and there is no other option, it is better to be patient, because even the factory protection will most likely not save you.

Saw conversion

Tools and materials:

Diagram of a carriage for a circular saw.

chain Saw;
flat steel roller;
nozzle for cutters;
reduction gear;
welding machine.

Electric saws and chainsaws are a gift from the 20th century, which fits very harmoniously into life, but there are situations when it is desirable to remake them, which is not easy. Please note in advance that this alteration is of a momentary nature, but if desired, you can repeat it over and over again without any damage (the replacement will take some time).

In order to get a circular saw, you only need to weld a movable wheel at the very end of the boom and cut off the end itself. The wheel must perfectly follow the contour of the cut element so that the chain does not stretch or fall off when moving.

An adapter for cutters is attached to the side of the wheel. This adapter is removable so that there are no difficulties when sawing with a chain.

With high-quality modification, the wheel will not in any way harm the performance of the chainsaw in the absence of cutters at this moment. In addition, the basic operating speed allows you to do without serious third-party modifications.

How to make a miter saw

Let's start assembling

We cut out a rectangular sheet of plywood and make a long cut on it, along which your trimmer will ride;
We screw two guides on top, for example, from an aluminum angle, to the width of the working plane of the circular itself;
From below to the plywood sheet you need to screw two stands with a height equal to the cutting depth of your saw (5.3 cm).

As a result, we get a guide along which the circular will move. Depending on how we fix it on the table using such a simple mechanism, we can make an accurate cut at any angle. The simplest version of the design is ready.

But what if we want our miter saw to be more functional in operation and look like a factory miter saw? In this case, you will have to show more ingenuity.

First, you need to make a bracket and a stand on which the circular will be attached. Chipboard (27 mm) is an excellent raw material for such a mechanism. Using self-tapping screws and aluminum corners, you will get a very decent upper part of the trim. And the springs attached to the top can make working on such a saw more convenient;
Secondly, we need to fix the tripod itself on a movable rotating stand, make a pendulum saw, thanks to which we will eventually be able to change the miter angle.

Carefully! Not only the quality of work and functionality of the trim, but also your personal safety will depend on what material you choose for the stand and tripod, and how securely you attach them to the stand. It’s not for nothing that they say that if a carpenter is experienced, then he is definitely missing a finger. Secure the circular as securely as possible! Safety is paramount!

Secure the circular as securely as possible! Safety is paramount!

As for the trim itself, everything is said about the assembly. However, if we decide to make a saw that looks like a factory saw, then it will be difficult to do without a table.

Jigsaw

A pendulum electric saw, better known as a jigsaw, has its own scope of use. This device is primarily intended for longitudinal, transverse and shaped cutting of sheet material. Using cutting tools with different characteristics, you can equally successfully work with boards, wood-based boards, plywood, cut laminate, and thin sheet metal.

The cutting part of a jigsaw is a file, which at one end is fixed in a clamp, performing reciprocating movements. Often the vibrations of the cutting tool are not limited to the vertical plane, but are supplemented by a pendulum movement, this provides greater speed and increases the service life of the blade.

In addition to conventional (straight) cutting, many models provide the ability to saw the workpiece at a precisely specified angle. To do this, the support table is rotated and fixed. This function significantly increases the scope of application of the jigsaw. An ordinary household tool allows you to cut at an angle of up to 45 degrees.

Security measures

When repairing an instrument, we must not forget about safety measures. First of all, you need to disconnect it from the power supply and do not plug it into the network until final assembly.

It is also worth remembering about electrical safety; you can repair parts of electrical equipment by using only the nominal value of the parts that were originally installed.

How to make a key for connecting a circular machine

To produce a key, you need to disassemble the frame of the angle grinder to find the wiring. They must be attached to the switch located at the finished base.

You can try an easier method: drag the start key with a zip tie. In this situation, the device must be connected to the network to start operations.