Design and principle of operation of metal planing machines

Metal planing machines are designed for roughing and finishing processing of workpieces of various shapes. Thanks to the ability to replace cutters, you can achieve the desired processing speed, cut various metals, and obtain the required level of productivity. Used in industry, workshops, repair shops.

Cross-planing machine (Photo: Instagram / kubanzheldormash)

Device

To perform the functions assigned to it efficiently, planing machines must include the following components:

• bed;
• control unit;
• a support with one or more tool holders;
• frame (on large machines the frame has a portal configuration, on smaller ones it is made in the form of a console);
• mechanism for moving the table and/or support;
• work table with T-shaped slots for precise positioning of the product;
• electric motor;
• pumping station for supplying lubricating and cooling media to the planing zone;
• a cross member that connects the elements of the frame and gives it the necessary rigidity;

The general classification index for such equipment includes an alphanumeric designation of the type XXXX. The first digit indicates the group number according to the classification tables. For planing machines, this is number 7. The second number indicates the type of machine (1 - single-column longitudinal planing; 2 - two-column longitudinal planing; 3 - cross-planing; 4 - slotting; 5 - broaching horizontal; etc.) . The third and fourth digits indicate the largest size of the workpiece.

Construction of planing machines

The main elements of a planing machine:

• electric motor;
• knife shaft;
• rollers;
• working surface.

The working surface consists of two parallel halves, between which a knife shaft is installed, the purpose of which is to remove the top layer of the workpiece. The board is fed for cutting manually or automatically. The board is fixed on the working surface with rollers.

The base is a homemade frame made from a metal corner 50x50 mm. The width of the base is determined by the gap between the shaft bearings (support). The housing is bolted to the frame. Metal rods act as homemade crossbars.

With your own hands, the work surface is made of two parts: fixed and movable. Both parts are superimposed on a welded frame made of metal angle 25 x 25 mm. The length of the frames should be 5 cm less than the length of the working surface. The width matches the width of the table. The working surface is made of a sheet of metal 3 mm thick.

The fixed frame of the table is welded with your own hands onto stands made of a rectangular pipe of 40 x 10 mm. Installation of the fixed part of the tabletop is carried out in the following order:

• with the help of wedges it is aligned parallel to the base and shaft;
• The stand is welded to the base.

The mobile part of the tabletop is made in the shape of a right triangle in cross-section. To raise or lower the table relative to the shaft, a screw connection (lanyard) is provided.

The tabletop is attached to the frame with countersunk screws and spacers. A cotter pin is attached to the fixed corner, which does not allow the height to change by more than 3 mm.

To support the workpieces, a ruler is provided, which makes it possible to change the inclination of the support.

Schemes of metal processing by planing

The last two digits of the marking indicate the main technological parameter of the equipment. As a rule, this is the largest dimension of the processed product in decimeters. For example, brand 7310 will indicate that this unit is a cross-planing unit and is intended for processing metal with a maximum plane length of up to 1000 mm. The letter in the designation (for example, 7A110) indicates a modification of the base model (for example, the presence of a hydraulic drive, an additional clamping unit, etc.). The presence of the letter F in the designation indicates that this equipment is equipped with a CNC system.

Planing equipment should be used in technological campaigns for the processing and production of various types of parts. The initial types of workpieces undergo a multi-stage processing process on machines of a certain type. The equipment produced at a machine-building enterprise uses parts of different configurations and dimensions.

Description of metal planing

Planing is a type of machining by cutting, in which, due to the reciprocating movement of the cutting tool, the surface is cut to the required shape and size, while ensuring surface roughness, dimensional accuracy and relative position of the planes.

During the process of planing metal processing, the workpiece gradually moves towards the cutting tool, while the planing cutter itself makes reciprocating movements in the horizontal plane. The movement of the cutter is considered the main one.

With each translational movement of the planing cutter, chips are removed from the part, the thickness of which is equal to the allowance. The thickness, shape and many other parameters of the chip depend on the material of the workpiece and the cutter, sharpening, condition and size of the cutting edge.

The appearance and shape of the chips can tell a lot about the deformations that occur during metal planing. Using planing, you can process straight open surfaces or screw surfaces.

We recommend articles on metalworking

• Steel grades: classification and interpretation
• Aluminum grades and areas of their application
• Defects in metal products: causes and search methods

The cutting movement (main feed) during planing processing is cyclical, and the removal of a layer of metal (or other material from which the workpiece is made) occurs during forward, not reverse movement. Metal planing is a low-speed type of machining.

VT-metall offers services:

The cutters are made of high-speed steels, which have the ability to withstand high dynamic loads during sharp impact cutting into metal materials without collapsing or losing their geometric shape and sharpening of the blade surface. After removing the metal layer with a direct main movement, the cutter makes a return movement at idle speed, thereby losing technological time. Therefore, this method of mechanical processing is not included in the list of productive technologies.

During planing processing, the cutting surface of the tool has a wedge-shaped geometric shape. In this case, the strength and hardness of the cutting tool must be higher than the same parameters of the workpiece.

Metal planing is used when working with grooves, protrusions, flat surfaces, and when creating grooved and shaped surfaces. This technology is used in the machining of guide beds of various metalworking equipment, sheet edges and guide rods, for the production of frames and slabs. This type of machine is used not only in serial production, but also when fulfilling single orders.

Types of metal planing machines

A classic metal planer carries out controlled removal of material of a certain thickness from the surface of the workpiece. It is distinguished by both the accuracy of the process and the technological schemes.

The main difference between planing machines and milling or turning machines is the configuration of the workpiece and the principle of operation. It does not have a rotation shape - its sides are often flat. The cutter processes one or more sides of the part, which is rigidly fixed on the work table.

Depending on the manufacturing technology, the following types of equipment are distinguished:

• Longitudinal planing machines (“1” – single column, “2” – with two columns). They can be used to give a certain shape to large samples. As an option, several medium-sized workpieces can be processed simultaneously. The cutter (there may be several of them) is fixed, and the blank, fixed on a special platform (table), moves with it.

• cross-planing (“3”). The cutting part moves, but the workpiece remains motionless. Used for the manufacture of large-sized parts. In addition, several types of operations can be carried out simultaneously to increase production speed. This depends on the number of cutters installed in the spindle slots of the cutter - from one to four. As a result of processing, recesses, grooves and recesses of a given shape are formed.

In addition, there are special-purpose machines. They perform similar operations, but differ in the form of influence on the workpiece:

• slotting (“4”). They make holes, select metal for grooves, protrusions, recesses, splines, grooves, that is, they are used for specific operations. Their working tool is called a “cutter”, the teeth of which perform the function of traditional cutters. The head can be rotatable, which allows processing in several planes, at an angle.

• Lengthy (“5” – horizontal; “7” – vertical). Mainly for removing chips from long workpieces.

• Shaped-planing machines (“9”). For processing curved surfaces (punches, bays of railway cars, etc.) or with ledges, when individual surface segments are located in different planes.

Elements that have the shape of a body of revolution are processed on some machines, and body objects are processed on others. The longitudinal combustion method is used when processing shaped and flat products. To achieve the highest level of cleanliness and surface quality of the product, it is worth using separate tools and technological processes.

Inferior to milling and turning models in productivity and price, this equipment wins in the low cost of the attached working tool and in the ease of sharpening it. For this reason, such machines are recommended to be purchased if you need to remove scale or form precise grooves and grooves in flat and shaped workpieces in a minimum number of passes

Electrical equipment, light, lighting

Many people prefer to do small carpentry work at home or in the countryside. This allows you to give free rein to your imagination and save money from the family budget. But to work with wood, you need available tools, for example, a planer, which you can make yourself.

The emergence of the planer

The first planing machine has been known since the time of Leonardo Da Vinci. But it did not influence the development of this equipment, since all records were lost. The scientist de la Hire from France in 1719 designed a planing machine, which was originally a modification of a lathe, and the movement was carried out by a rope from the beam.

And today there are many different planing machines, which, depending on the work performed, are divided into the following groups: general purpose machines, specialized and special machines.

General purpose machines include longitudinal planing and cross planing. Special machines are designed to perform specific detailed operations and are mainly used in mass production.

Specialized machines include cross-planing machines with a movable carriage for working with heavy parts, pit longitudinal planing machines for processing heavy and large parts, and edge-planing equipment for processing the edges of large sheets.

The longitudinal planing machine is designed for processing large workpieces. Such devices come in single- and double-column types. In the process of cutting metal on a longitudinal planing machine, movements are transferred to the workpiece, which is previously fixed on the table of the planing machine. Its main characteristics are the width and length of the planing. The maximum length reaches up to 25, and the width reaches 5 meters.

A cross-planing machine is used to work with medium or small workpieces. The movements are transmitted to the cutting tool, and not to the workpiece. This tool is placed on a slide. A characteristic of such a planing machine is the stroke length of the slide, which reaches 2.5 meters. You can move the table where the workpiece is fixed in horizontal and vertical planes.

Purpose of planing machines

Planing machines are necessary for processing ruled surfaces - vertical, horizontal and inclined planes. Ruled surfaces also include shaped surfaces, which are a combination of planes located at different angles.

With the help of metalworking and woodworking planing machines, it is also possible to process shaped surfaces, the profile of which has curved sections that are formed by circular arcs or complex curves. Planing machines process not only flat surfaces, but also grooves, straight grooves, ledges and various recesses. It is possible to process metal in a closed loop.

Small-sized parts and large forgings, welded structures and castings that have a length of up to 12 meters, a width of up to 6 meters and a height of up to 3 meters are processed using a planing machine. The weight of such parts can reach up to 200 tons.

On planing machines, the workpiece is processed along a plane, thickness or angle, thanks to which the lumber acquires ideal evenness. On a double-sided jointing machine, the layer and the edge of the part are simultaneously processed. Parallel planes are processed using double-sided thicknessing equipment.

Metal-cutting machines of a planing nature are used in special machine shops for processing all kinds of parts in the automotive industry. They are also found in many repair shops and tool shops. They are well suited for working with parts made of steel, various non-ferrous alloys and even some types of plastic.

Wood planing machines are used to process the surface of wood after sawing “clean”, making lumber and parquet. They are designed for processing straight workpieces and plane milling. Using different sets of knives allows you to work with soft (spruce, pine) and hard (poplar, oak, beech) wood species.

Cutters for metal planing machines

Manual planer

Planing machines for metal processing are used to complete technological lines with high productivity and repair shops. Their advantage is relatively simple setup and maintenance.

The main factor in the correct processing of the workpiece is the choice of the appropriate cutter. It must be designed to perform a specific operation or have a universal application. To do this, in the production process of cutters, high-speed steel blanks are used or carbide brazing is made.

Types of cutters for planing equipment

Cutters used for processing parts on a metal planing machine are divided according to a number of characteristics:

• In the direction of delivery; (left and right)
• According to the shape of the head; (straight, bent, with a retracted head)
• By manufacturing method; (solid and composite)
• By type of work performed (through roughing and finishing, shaped, cutting, grooving, etc.)

The process of planing metal occurs only with a working cutter, or on tables with a firmly fixed workpiece.

At the moment when the cutting tool is tightly fixed in the folding holder, its process of wear and exhaustion will take much longer, since during the return stroke it begins to fold back and move freely over the entire surface.

Main criteria for choosing a cutter model:

• type of equipment - for longitudinal or transverse operations;
• cutting edge material. Affects the speed and accuracy of work;
• cutter shape. Depending on this parameter, grooves, holes or grooves will be formed on the surface of the part.

There are several types of operations carried out on a longitudinal planing machine. They can be pass-through, finishing, shaped, trimmed or cut-off. To increase the service life of cutters, it is recommended to use equipment with a folding locking head. After initial processing, the cutter returns to its original position. During the return stroke, it should not come into contact with the surface of the workpiece.

The most common are longitudinal planing machines. They are characterized by relatively small dimensions and ease of operation. Particular attention should be paid to the quality of cutting tools. To ensure an uninterrupted technological process, it is necessary to have a small supply.

Types of planing units

After analyzing the geometric dimensions of the workpiece, as well as the properties of the metal from which it is made, the surface finishing is carried out on a longitudinal or transverse planing unit.

The fundamental difference between these metal cutting machines is determined by the method of moving the cutter. A table moves on the longitudinal planing unit, with the workpiece fixed on it.

Large blanks are processed in this way. When cross planing is performed, the cutter moves and the workpiece is fixed on the table. This method is used when processing medium-sized parts. In each specific case, cutters of the appropriate configuration are selected.

The same class of metal processing equipment includes slotting, broaching and shaped-planing mechanisms.

Using cutters of various shapes, such machines perform operations of selecting recesses and grooves, turning channels and cutting holes.

One of the features of a metal planer is the number of cutting tools installed.

IMPORTANT TO KNOW: Types of desktop metal milling machines

Some models are designed for simultaneous fastening of several cutters at once.

The following machine models are produced according to these parameters:

• one-sided;
• double sided;
• four-sided.

The more cutting tools installed on a planer-type device, the higher its productivity.

Construction of a longitudinal planing unit

As prescribed by the technical characteristics, longitudinal planing machines are used for processing surfaces on body and asymmetrical parts cast from cast iron or alloys of non-ferrous and ferrous metals.

The dimensions of the workpiece being processed are determined by the technical capabilities of the planing unit. The initial workpiece to be processed is placed on the table.

The table is capable of performing reciprocating movements. In this case, the cutter fixed in the support remains motionless.

When the table is idling, the support moves to the side, allowing the table to move freely to its starting point.

This complex movement allows you to process large workpieces with several cutters at once.

A longitudinal planing machine for the production of metal products is composed of a frame, a table, supports, a cross member, electrical equipment, a lubrication system and other components.

Each model has its own length and width of the working surface of the table. A common element for all models is the control panel.

When processing parts with complex geometric dimensions, several cutting tools can be installed on the support. This technique reduces the time for processing the product.

Design of a cross-planing unit

A cross-type metal planing machine is installed in production lines where small and medium-sized parts are processed.

The unit is used for planing horizontal, vertical and inclined surfaces.

As in any metalworking machine, the main elements of the cross-planing unit are the bed and the base.

IMPORTANT TO KNOW: Using 3D milling and engraving machines for metal

All components and devices that are designed to ensure fastening and movement of the corresponding elements are attached to this support. The part is fixed on the table at the specified coordinates.

The support, with the cutter fixed in it, is given movement within certain limits.

In the process of metal processing, parts assemblies and structural elements perform complex movements, the purpose of which is to carry out a given program.

The planing unit for metal of the cross type can operate under manual control or according to a given program.

The main one is the reciprocating movement of the slider on which the cutting tool is attached.

Auxiliary is the movement of the table on which the workpiece is fixed. The speed of movement of the slider is controlled using a special gearbox, like in a car.

Before processing any part, all mechanical components of the unit must be lubricated with machine oil.

Review of the best models of cross-planing machines

Planing equipment with a reciprocating movement of the cutter and a stationary workpiece mounted on the feed table has a limited scope of application and is used primarily in small-scale and one-time production. Nevertheless, it has its advantages and is considered worthwhile when it is necessary to perform roughing and finishing operations for planing and preparing grooves in relatively small metal workpieces with a flat and shaped shape.

The model range of these machines is limited, but all offered devices are valued for their simplicity of layout, high processing accuracy, reliability and unpretentiousness.

How to choose a planing machine

Criterias of choice:

• desktop area;
• installed engine power;
• speed of movement of the cutter relative to the workpiece;
• available cutting methods;
• table configuration;
• possibility of positioning the cutter: angle of inclination, trajectory of movement;
• degree of protection of the housing from dust and moisture;
• maximum permissible weight of processed parts;
• manufacturer, warranty period, availability of additional options to expand functionality.

Equipment configuration (Photo: Instagram / kubanzheldormash)

Advantages and disadvantages

Advantages of planing machines:

• versatility of application - processing of various types of metals;
• selection of optimal cutting speed;
• wide selection of cutting tools;
• the possibility of roughing or finishing to obtain the desired level of surface roughness;
• high strength of the body, capable of withstanding increased loads from the cutting tool and the weight of the part;
• convenient control;
• formation of surfaces of complex shape;
• high reliability of installed components and assemblies.

Flaws:

• loss of time moving the cutter relative to the workpiece;
• inertia of moving mechanisms;
• high level of vibrations;
• engine noise;
• the difficulty of obtaining high engine speeds under load or at idle in a short period of time.

Scope of application

This equipment is not highly productive; due to the idle reverse motion and the inadmissibility of high cutting speeds due to inertia, the dimensions of the workpieces processed are limited; longitudinal planing machines are practically not used for mass production of metal products. But they are the best when it is necessary to form complex grooves and profiles using cutters or the use of rotating cutters is inadmissible.

A wide variety of working tools are fixed in the support assembly of such machines, including passing, trimming, slotting and shaped cutters, which allow roughing and finishing planing operations to be performed with their inherent accuracy (average deviations do not exceed 0.03 mm per 300 mm length of the metal workpiece).

In particular, the cross-planing machine is successfully used:

• When planing horizontal planes with the help of universal cutters, vertical ones with scoring cutters complete with stops.
• Processing of parallel planes with division of the process into two stages and sequential execution of work
• When planing inclined planes by installing the support at an angle and ensuring its feed in a parallel direction. The maximum effect is achieved when it is necessary to process a narrow strip (10-30 mm); with such parameters, all the advantages of fixing a wide and non-rotating cutter are manifested.
• When making grooves and grooves, including keyways.
• When planing chamfers using concave, convex and similar cutters. In the manufacture of gears, couplings and cams (subject to the use of additional specialized and dividing devices).

Inferior to milling and turning models in productivity and price, this equipment wins in the low cost of the attached working tool and in the ease of sharpening it. For this reason, such machines are recommended to be purchased if you need to remove scale or form precise grooves and grooves in flat and shaped workpieces in a minimum number of passes.

Design and principle of operation of the equipment

The layout of the units is simple and includes several large elements:

1. A foundation slab with a stable frame secured with bolts. The metal planing machine is a fairly massive structure and weighs at least 1800 kg.

2. A slider with a built-in support that holds and regulates the position of the planing cutter and its feed mechanism.

3. Cabinet or casing with a motor (mostly asynchronous) and electrical equipment and drive. Planing types of machines are equipped with rocker, crank, gear, portable or hydraulic transmission mechanisms, the first group is the most common, but has a relatively limited stroke length of the slide (up to 700 mm), varieties with movement within 700-1000 mm are usually hydraulically powered and have a separate drive for accelerated return of the caliper.

4. Work table with stands for additional fastening and increased rigidity and guides for horizontal movement. In improved modifications it is inclined.

Transverse planing in these machines is carried out using a reciprocating slider with a fixed cutter with different sections and shapes; during contact with the tool, the workpiece itself remains motionless.

The removal of metal or the formation of a groove is carried out during the working stroke of the caliper assembly, followed by its idling (usually accelerated several times) with a return to its original position. Upon completion of each return operation, the machine moves the table feed in a transverse direction relative to the main stroke.

The main dimensional characteristic is the stroke length of the slider, varying from 200 to 2400 mm, with an average range of 500-700. The support with the cutter is capable of moving in the longitudinal and vertical direction and rotating around a horizontal axis. The speed of its movement, along with the dimensions and feed parameters of the table, have a direct impact on the functionality and dimensions of the workpiece being processed. The devices are powered by a three-phase network and have simple controls.

Types of devices

A planing device for a metal surface can be of two types at once: longitudinal planing and transverse planing. The principle of processing such parts on equipment will differ significantly .

Longitudinal planing machines are designed to work with a fairly short surface. That is why in them the movement occurs on the table to which the part being processed is attached. While the cutter itself will be installed by the cutting head of the support, and also relative to the bed, the machine will not carry out any movement.

In a cross-planing machine, the work occurs in a completely different way: the cutter produces movement, and the semi-finished product installed on the table remains stationary.

Planing types of machines are significantly inferior to milling machines in their functioning, since they have an idle stage, while the workpiece or the same cutter moves to a new position. In this case, the drive will not be very energy-intensive , since the process of rotational movement of the working device (as in a milling machine) will require significantly greater costs from the drive electric motor.

Overview of the machine range

The main developer and manufacturer of planing equipment of this group is the Orenburg SZ; many domestic companies offer to purchase ready-made, repaired or modernized devices, Pressmash, Stanochny Mir); among used machines, the products of the Gomel SZ have good reviews. The models have a generally similar design, the differences are manifested in the dimensions, power and parameters of the workpiece being processed. The main indicators of the most common of them are presented below:

7305T

The basic model of a cross-planing machine, supplied without a slotting head at a price of 680,000 rubles and used for processing flat and shaped metal products in all planes, including inclined.

This equipment is distinguished by its increased rigidity of the frame and guide and has a good power resource (up to 5500 W), facilitating the precise performance of finishing, roughing and fine planing.

The machine is equipped with a 500×400 rotary table with 25 feeds and three T-shaped slots for gripping workpieces with a slide stroke of up to 510 mm and an outreach of up to 560; the maximum distance between the horizontal plane and the guides is 40 cm.

7307TD

Expanded modification 7305T with a slotting head and a slider stroke increased to 710. By analogy with the previous one, this cross-planing machine is recommended to be purchased when processing flat and shaped workpieces made of hard materials (the permissible cutting force reaches 19.6 kN); with equal power and table movement speed, it wins in functionality and increased working space.

This affects the price; in new condition, this model can be purchased from 800,000 rubles and above. At the same time, its optimal scope of application is enterprises with single and small-scale production conditions.

7B35

Planing equipment for processing with a cutter workpieces with a length of up to 500 mm inclusive and forming grooves and grooves in them with different shapes and depths within the cross-section of the working tool 20×32 mm. The model was developed for installation in repair, mechanical and tool shops of mechanical and instrument manufacturing enterprises with relatively small production volumes (single and small-scale production of metal parts).

In the basic version, 7B35 has a fixed table with 20 feeds and manual, mechanical and root movement; models with universal rotary structures are made to order. The machine is equipped with a centralized lubrication unit and a chip collector; the estimated costs for purchasing it in basic configuration and in good condition are 600,000 rubles.

7M36 and 7M37

The cross-planing machine of the Gomel SZ is the base for models with a universal rotary table and copying devices, used for processing their metal surfaces with a slide length of up to 700 mm inclusive. At the moment, the model has been discontinued from main production and replaced with improved slotting analogues, but thanks to the reliability of the components and hydraulic drive, it is still used in machine shops of machine-building enterprises and is sold in used condition at a price of 140,000 rubles and above.

The machine has 2 electric motors (the main one ensures the start of all components, the auxiliary one ensures rapid movement of the worktable with dimensions of 450×700 and 560×1000 mm, respectively), the lubrication of its frame and slider guides is carried out automatically, the same applies to the feed of the support and cutter.

Electrical equipment, light, lighting

Many people prefer to do small carpentry work at home or in the countryside. This allows you to give free rein to your imagination and save money from the family budget. But to work with wood, you need available tools, for example, a planer, which you can make yourself.

The emergence of the planer

The first planing machine has been known since the time of Leonardo Da Vinci. But it did not influence the development of this equipment, since all records were lost. The scientist de la Hire from France in 1719 designed a planing machine, which was originally a modification of a lathe, and the movement was carried out by a rope from the beam.

And today there are many different planing machines, which, depending on the work performed, are divided into the following groups: general purpose machines, specialized and special machines.

General purpose machines include longitudinal planing and cross planing. Special machines are designed to perform specific detailed operations and are mainly used in mass production.

Specialized machines include cross-planing machines with a movable carriage for working with heavy parts, pit longitudinal planing machines for processing heavy and large parts, and edge-planing equipment for processing the edges of large sheets.

The longitudinal planing machine is designed for processing large workpieces. Such devices come in single- and double-column types. In the process of cutting metal on a longitudinal planing machine, movements are transferred to the workpiece, which is previously fixed on the table of the planing machine. Its main characteristics are the width and length of the planing. The maximum length reaches up to 25, and the width reaches 5 meters.

A cross-planing machine is used to work with medium or small workpieces. The movements are transmitted to the cutting tool, and not to the workpiece. This tool is placed on a slide. A characteristic of such a planing machine is the stroke length of the slide, which reaches 2.5 meters. You can move the table where the workpiece is fixed in horizontal and vertical planes.

Purpose of planing machines

Planing machines are necessary for processing ruled surfaces - vertical, horizontal and inclined planes. Ruled surfaces also include shaped surfaces, which are a combination of planes located at different angles.

With the help of metalworking and woodworking planing machines, it is also possible to process shaped surfaces, the profile of which has curved sections that are formed by circular arcs or complex curves. Planing machines process not only flat surfaces, but also grooves, straight grooves, ledges and various recesses. It is possible to process metal in a closed loop.

Small-sized parts and large forgings, welded structures and castings that have a length of up to 12 meters, a width of up to 6 meters and a height of up to 3 meters are processed using a planing machine. The weight of such parts can reach up to 200 tons.

On planing machines, the workpiece is processed along a plane, thickness or angle, thanks to which the lumber acquires ideal evenness. On a double-sided jointing machine, the layer and the edge of the part are simultaneously processed. Parallel planes are processed using double-sided thicknessing equipment.

Metal-cutting machines of a planing nature are used in special machine shops for processing all kinds of parts in the automotive industry. They are also found in many repair shops and tool shops. They are well suited for working with parts made of steel, various non-ferrous alloys and even some types of plastic.

Wood planing machines are used to process the surface of wood after sawing “clean”, making lumber and parquet. They are designed for processing straight workpieces and plane milling. Using different sets of knives allows you to work with soft (spruce, pine) and hard (poplar, oak, beech) wood species.