Specific heat of fusion - formula, table of units of measurement for a substance

Let us take a substance weighing 1 kg preheated to its melting temperature. We will provide it with thermal energy to melt this substance.

The energy that we spend to melt 1 kg of a substance is called the specific heat of fusion.

This heat is called specific value, since it is per 1 kg of substance.

The specific heat of fusion is the energy that we will expend to melt 1 kg of a substance if this substance has previously been heated to its melting temperature.

This value is denoted by the small Greek letter \(\large \lambda\) - lambda.

\(\large \lambda \left( \frac{\text{J}}{\text{kg}}\right)\) – specific heat of fusion.

Notes:

1. In order for a crystalline solid to begin to melt, it must be heated to its melting point.
2. The melting point of various substances can be found in a physics reference book.
3. If a crystalline solid melts at its melting point, then it will solidify (crystallize) at the same temperature when it loses thermal energy.
4. In physics, other specific quantities are also used, for example, the specific heat of combustion of fuel.

Before a substance can be melted, it must be heated to its melting point.

Content

Looking at the graph of ice melting and solidification in the last lesson, we found out that during the melting process the temperature of the ice does not change. The temperature will continue to rise only when the ice completely turns into liquid. We observed the same thing during the crystallization of water.

But when ice melts, it still receives energy. After all, during melting we do not turn off the burner - the ice receives a certain amount of heat from the fuel burning in the alcohol lamp (or other heater). Where does this energy go? You already know the law of conservation of energy - energy cannot disappear.

In this lesson we will look in detail at what happens during the melting process, how energy and temperature change. This will allow us to move on to a new definition - specific heat of fusion.

Thematic assignments

The study of thermal phenomena and their features, which include specific heat, is included in the school curriculum in physics for high school. Thematic tasks are used to test the mastery of the material covered.

In addition to the usual text conditions, tasks to find the specific heat of vaporization are in most cases accompanied by graphs displaying the temperature changes that occurred with the substance as it absorbed heat.

But graphical tasks are not the most interesting. Some of the most entertaining tasks include:

1. A piece of ice, placed at a temperature of -90 degrees Celsius, began to be heated by supplying constant thermal power to it. After 63 seconds from the start of heating, the ice reached the temperature required for melting. It is required to find the time in seconds that the process of melting ice will take from the moment it reaches the desired heating, provided that there is no loss of heat. Answer: 110 seconds.
2. A piece of lead, which was at a temperature of +27.5 degrees Celsius, began to be heated by applying constant thermal power to it. 39 seconds after the start of heating, the temperature of the lead reached the melting level (+327.5 degrees Celsius). It is necessary to determine the duration of the lead melting process in seconds from this moment, taking into account the absence of heat losses. Answer: 25 seconds.

Comparing the answers to these problems allows us to estimate the difference between the specific melting values ​​of ice and lead. In the first it is very large, and in the second, on the contrary, it is small. This is not surprising - the amount of heat required for melting directly depends on the properties and characteristics of the substance, in particular, on the energy of the bonds connecting the particles of this substance to each other.

The role of the large specific value that ice has is invaluable both for nature and for humanity. If this figure had been lower, then in the spring all the ice and snow would have melted, which would have had dire consequences. The streams of water resulting from such melting would wash away everything in its path.

Fortunately, ice and snow masses are not capable of melting in a few moments . The physical properties of these substances once again prove that nature is a brilliant and inimitable creator.

Change in internal energy and temperature during melting

So where does the energy that we impart to the body go during melting?

You know that in crystalline solids, atoms (or molecules) are arranged in a strict order (Figure 1). They do not move as actively as in gases or liquids. However, they are also in thermal motion - oscillating.

Figure 1. Structure of crystalline quartz

Take another look at the ice melting and solidifying graph (Figure 2).

Figure 2. Graph of ice melting and solidification

The ice is heated in section AB. At this time, the average speed of movement of its molecules increases. This means that their average kinetic energy and temperature also increase. The range of vibrations of atoms (or molecules) increases.

This happens until the heated body reaches its melting point.

At the melting temperature, the order in the arrangement of particles in crystals is disrupted.

This is how the substance begins the transition from solid to liquid.

This means that the energy that the body receives after reaching the melting temperature is spent on the destruction of the crystal lattice. Therefore, body temperature does not increase - part of the BC graph.

Why does a solid become liquid?

Heating a solid body leads to an increase in the kinetic energy of atoms and molecules, which at normal temperatures are located clearly at the nodes of the crystal lattice, which allows the body to maintain a constant shape and size. When certain critical speed values ​​are reached, atoms and molecules begin to leave their places, bonds are broken, the body begins to lose its shape - it becomes liquid. The melting process does not occur abruptly, but gradually, so that for some time the solid and liquid components (phases) are in equilibrium. Melting refers to endothermic processes, that is, those that occur with the absorption of heat. The opposite process, when a liquid solidifies, is called crystallization.

Rice. 1. Transition of the solid, crystalline state of a substance into the liquid phase.

It was discovered that until the end of the melting process the temperature does not change, although heat is constantly supplied. There is no contradiction here, since the incoming energy during this period of time is spent on breaking the crystalline bonds of the lattice. After the destruction of all bonds, the influx of heat will increase the kinetic energy of the molecules, and consequently, the temperature will begin to rise.

Rice. 2. Graph of body temperature versus heating time.

Change in internal energy and temperature during solidification

During hardening, the opposite happens.

The average speed of movement of molecules and their average kinetic energy in a liquid (molten substance) decreases upon cooling . This corresponds to the section of the DE graph in Figure 2.

Now the attractive forces between the molecules can hold them close to each other. The arrangement of particles becomes ordered - a crystal is formed (section of the EF graph).

Where is the energy released during crystallization spent? The body temperature remains constant during this process. This means that energy is spent maintaining this temperature until the body completely hardens.

Now we can say that

At the melting point, the internal energy of a substance in the liquid state is greater than the internal energy of the same mass of substance in the solid state.

This excess energy is released during crystallization and maintains the body temperature at the same level throughout the solidification process.

general information

A correct understanding of the specific heat of fusion is impossible without studying the key features of the melting process itself. Both during melting and during crystallization of a substance, its internal energy changes. During the first process, it increases, since it is invariably accompanied by heating - the main condition for increasing energy. The temperature during melting remains unchanged. In a certain sense, this is paradoxical, because internal energy can be characterized by temperature.

However, there is a very simple and logical explanation for the increase in energy at a constant temperature. During the melting process, the spatial lattice of the crystalline body is destroyed, and all the energy is spent on this. The destruction of the crystal lattice requires the expenditure of a certain amount of energy from some external source. As a consequence, during the melting process the internal energy of the body increases.

In the process of solidification of a body or, in other words, crystallization, on the contrary, its internal energy decreases, since it gives off heat to the bodies that surround it. Solidification (crystallization) is the reverse process in relation to melting. Molecules of a substance form a common (single) system, and during this unification, the excess energy given off by the components of the substance is absorbed by the external environment.

Basic information about the heat of fusion

According to the law of conservation of energy, a body absorbs during melting and gives off during solidification (at the temperature required for each of these processes) an equal amount of heat.

The heat of fusion is the amount of heat that is necessary for a physical body at the melting point to transform into a liquid state from a solid. This thermal phenomenon is a special case of a phase transition in thermodynamics.

The heat of melting is influenced by the mass of the melting substance, as well as the properties that it possesses and which are characteristic of it. This connection between the heat of melting of a physical body and the type of substance, expressed through the dependence of the first on the second, is measured by a specific value.

Melting a substance requires the same amount of heat that is released during crystallization, therefore, the definition of the specific value of heat exists in two equivalent concepts - for melting and for crystallization. This quantity also has an alternative name - enthalpy of fusion.

Measurement Features

Physicists have experimentally established that to transform the same substance into a liquid from a solid state, different amounts of heat are required . Then the experimental researchers decided to compare these indicators at the same mass of the substance. This is how the concept of specific value appeared.

According to its simplified definition, it shows the ratio of the heat of fusion of a body of a certain substance and its mass. This indicator is considered the main characteristic for both melting and crystallization.

The unit of measurement of this quantity, according to the International System of Units, is J/kg (joule per kilogram). The specific indicator is denoted by the letter lambda (less commonly read as lambda) from the Greek alphabet (analogous to the Cyrillic letter “l”).

The specific heat of fusion is found using the formula: lambda = Q/m, where Q is the designation of the amount of heat that the substance received during melting or released during crystallization, and m is the mass of the substance (melting or crystallizing). The absence of a temperature indicator in the dimension is due to the fact that the temperature does not change either during melting or during crystallization.

The specific value during melting is always positive, and during crystallization it is negative. The only exception to this rule exists (or rather, is known to science) - this is a chemical element of the periodic system called helium , which is under high pressure. It is negative when melted.

To convert a substance in the amount of one kilogram from a solid to a liquid state, you need to heat it to the melting point and add heat to it in an amount equal to the specific indicator. During the crystallization of one kilogram of a substance, heat is released in exactly the same amount.

To find the amount of heat required to melt or crystallize a substance at the appropriate temperatures, the specific value must be multiplied by the mass of the substance. For crystallizing bodies, this indicator will have a minus sign, that is, negative. This is due to the fact that during the hardening process all the heat is lost - released without being retained.

comparison table

A table with the specific heat of fusion of some substances and chemical elements (substances in the table are not arranged in alphabetical order, but by decreasing specific index):

Specific values ​​for these substances are considered tabular (constant and known) values, so there is no need to make calculations to find them.

Specific heat of fusion

It has been experimentally proven that different amounts of heat are required to transform crystalline solids of the same mass into liquid. In this case, bodies are considered at their melting temperatures.

The specific heat of fusion is a physical quantity that shows how much heat must be imparted to a crystalline body weighing $1 \space kg$ in order to completely transform it into a liquid state at the melting temperature.

• denoted by the letter $\lambda$
• unit of measurement — $1 \frac{J}{kg}$

Peculiarities

Along with the great variety of known metals, the element in question has a relatively small thermal capacity with an average degree of heating. The value for steel corresponds to 440 – 550 J/(kg deg), cast iron – 370 – 550 Joules/(kg deg), nickel – 440 J/(kg deg).

Special attention should be paid to the fact that the indicators of heavy metal components are not high. Therefore, famous physicists have identified the following relationship: the higher the density, the lower the heat coefficient.

Specific heat of fusion of certain substances

Table 1 presents the experimentally obtained values ​​of the specific heat of fusion for some substances.

Table 1. Specific heat of fusion of certain substances (at normal atmospheric pressure)
The specific heat of fusion of gold is $0.67 \cdot 10^5 \frac{J}{kg}$. What does this mean?

In order to melt a piece of gold weighing $1 \space kg$, taken at a temperature of $1064 \degree C$ (the melting point of gold), to a liquid state, we will need to spend $0.67 \cdot 10^5 \space J$ of energy.

It has been experimentally proven that

When a crystalline substance solidifies, exactly the same amount of heat is released that is absorbed when it melts.

That is, during the crystallization of molten gold weighing $1 \space kg$, $0.67 \cdot 10^5 \space J$ of energy will be released.

What is heat characterized by?

Heat transfer implies an increase in the internal energy of some bodies and its decrease in other bodies. All this is accompanied by the absence of changes in mechanical actions and work. However, the internal energy of the heating object decreases, and the heated body increases.

As mentioned, the heat transfer process is determined by the amount of heat. This concept refers to the change in the internal energy of an object that occurs at the end of heat exchange. The calculation often uses a physical unit called a calorie.

A calorie is equal to the amount of heat required to warm a gram of water by 1° Celsius. The researchers found that to do this, you need to do 4.18 J of work. This means that a calorie is equal to 4.18 Joules.

Since heat equals the change in energy inside an object, we must say that c represents how much the energy of one kg of object changes when it is heated.

Calculation of the amount of heat required to melt or solidify a substance

To calculate the amount of heat $Q$ required to melt a crystalline body of mass $m$, taken at its melting point and normal atmospheric pressure, the specific heat of fusion $\lambda$ must be multiplied by the body mass $m$: $Q = \lambda m $.

We can express from this formula the mass $m$ and the specific heat of fusion $\lambda$:

$m = \frac{Q}{\lambda}$, $\lambda = \frac{Q}{m}$.

The amount of heat that will be released during hardening is calculated using the same formula. But it must be remembered that the internal energy of the body will decrease.

Related quantities

The so-called specific indicators exist to characterize not only melting and crystallization. In physical science, in addition to these processes, specific heat values ​​are characterized by:

• steam generation;
• condensation;
• heat capacity.

The specific heat of vaporization and condensation reflects the volume of heat required to convert a unit mass of liquid into vapor and vice versa. The formula for this quantity is: Q/m. So, in essence, it is the same as the enthalpy of melting and crystallization.

As for specific heat capacity, it is an indicator of the ratio of heat capacity and mass of a substance. It is equal to the volume of heat, the transfer of which to a unit mass of a substance is necessary to change its temperature by one degree.