Making bends from galvanized steel with your own hands

Galvanized chimney pipe: types, which is better and how to make it yourself

Hello, dear reader! Today we will consider the question of how good a galvanized pipe is for a chimney. The need for such an assessment arises every time before the owners of private houses when constructing or replacing a chimney. Let's find out all its pros and cons, how best to use it and whether it can be done with your own hands.

What is

The product is a metal pipe coated with a layer of zinc (pictured).

The coating creates a protective film that protects the iron from rust for a certain period, until the zinc layer is mechanically damaged.

Material characteristics

Zinc is a metal with a melting point of 419 C.

The composition of the zinc coating includes an alloy of zinc (99.97%), aluminum, lead and other metals. The layer thickness is standardized by GOST and ranges from 10 to 60 microns.

In air, zinc is covered with a thin film of oxide, which acts as a protection for steel from corrosion.

Galvanized steel is resistant to precipitation and temperature changes.

Convenient to process, easy to bend, roll, stamp and other mechanical loads.

Can galvanized pipes be used for chimneys?

Chimneys with zinc coating are used under certain conditions.

When zinc is heated to 419°, it begins to release substances harmful to humans. Therefore, it is recommended to install outlets made of this material in smoke exhaust systems where the temperature does not exceed 350°C.

The 2009 Ministry of Emergency Situations rules prohibit the use of metal smoke removal agents for coal-fired stoves.

In addition, a single-wall galvanized outlet will burn out after one or two seasons. In practice, it is used as an outer casing in double-walled structures with insulation.

Advantages and disadvantages of galvanized pipes

Users include the following advantages of a galvanized chimney pipe:

• long-term immunity to corrosion;
• rapid heating of the chimney and, as a result, ensuring good draft;
• simple assembly method;
• a smooth surface inside the channel, which does not allow soot to linger on the walls;
• Possibility of venting through the wall of the building.

Flaws:

• short service life of a single-wall outlet;
• when cutting a product, the cut lines begin to rust after a short time;
• minor damage leads to the destruction of the protective layer;
• formation of a large amount of condensate.

Types of galvanized iron pipes

Based on the design features, two types of these products are distinguished: single-circuit and double-circuit insulated.

The first ones consist of single-wall bends. They are installed in heating devices with low temperatures or in brick chimneys.

The second ones include two outlets: an internal one made of stainless steel and an external one made of galvanized steel. An insulating agent is placed between them. They are called “sandwich” pipes and have managed to prove their effectiveness.

Life time

Galvanized outer pipe in a sandwich, when properly installed and manufactured, can last 45 years.

A single-circuit chimney will burn out quickly; its service life, depending on the intensity of use, will be one to two years.

What is better galvanized or stainless steel?

It is recommended to make the initial section of the chimney channel from the boiler, where the temperature is especially high, from stainless steel. The inner pipe of the sandwich is made from it, which allows it to be used in any smoke removal system.

Of course, this type of steel is the most durable and rust-resistant. In these parameters it is superior to galvanization. Its main drawback is its high price.

To reduce the cost of sandwiches, galvanization is used to make the casing.

Make it yourself or buy it

Making a pipe from sheet material is not an easy task. Requires certain equipment and skills. But if the length of the chimney is short, and it is straight, without bends or bends, you can do this work yourself.

In other cases, it would be wiser to purchase or order a galvanized chimney from professionals.

Selection tips and approximate price

Manufacturers offer a large selection of both single-circuit galvanized bends and sandwich pipes with a galvanized shell. There are certain parameters by which you should select elements for the chimney:

• the diameter of the boiler outlet pipe must be equal to or less than the cross-section of the chimney outlet;
• attached chimneys can have no more than three bends along the entire length of the channel.
• Manufacturers indicate the required chimney diameter for boilers in the unit’s passport;
• The wall thickness for the outer casing must be at least 0.5 mm, usually 0.55 mm is used.

The price of single-circuit galvanized steel pipes depends on the diameter and thickness of the sheet metal. A meter bend d=110 mm costs 190 rubles, and d=250 mm costs 390 rubles.

A stainless steel + galvanized sandwich of the same diameter, 0.5 mm thick and 100 cm long will cost 1,230 rubles.

Making galvanized pipes with your own hands

A special feature of a factory-made galvanized pipe is its reliable welding seam.

If you have an argon unit at home and you are a big welder, this makes a difference. Surely what you will get is not a pipe, but a feast for the eyes.

First you need to choose a galvanized sheet for the pipe. Professionals make bends with walls 0.55 mm thick. At the same time, it must be taken into account that the thinner the material, the easier it is to bend.

Required tools and materials

You will need:

• hand scissors for metal;
• mallet with a wooden striking part;
• roulette;
• square;
• metal ruler;
• pencil, preferably a construction pencil;
• pliers.

For the convenience of bending work, a simple workbench is equipped where markings are made. A metal corner (40×40 mm or more) with a length of at least 100 cm, a steel round shape of the required diameter, is attached to the table.

Cutting out the workpiece

Let's look at how to make a pipe with a cross-section of 100 mm.

Calculate the width of the workpiece:

• determine the circumference as the product of the cross section and the value of pi equal to 3.14;
• 15 mm are allocated for the bends for the connecting seam.

In total, for a 100 mm bend, a workpiece with a width of 3.14 × 100 mm + 15 mm ≈ 330 mm is cut out.

Take into account that the pipes are made slightly cone-shaped for ease of installation using the socket method. Therefore, one side measures 330 mm, the other 340 mm (in the figure).

Formation of a profile

On the cut-out workpiece, mark a fold line for a fold of 5 mm on one side, twice 5 mm each on the other.

The sheet is laid on a workbench, the edge is aligned with the corner. Using a mallet, gradually bend it at a right angle. Then the workpiece is turned over and the fold is placed on the canvas.

In the same way, a 10 mm bend is made on the other edge of the sheet, and another 5 mm wide on it.

Next, the workpiece is manually bent on the forming tube, using a mallet.

Processing the butt seam

After obtaining a round shape of the workpiece, it is placed on a round form or an additional corner, the folds are connected into a lock, tapping them along the edges with a mallet. At the narrow end of the future pipe, the folds are slightly cored. Tap the entire length of the joining seam with a mallet, compacting the folds. The seam becomes almost permanent.

Manufacturing procedure

Having decided on the materials and steel grade of the future blade, it’s time to get to work and make a knife from a drill. Don’t forget about fireproof gloves and goggles; scale will fly when forging:

1. A mandatory process that is rarely mentioned is annealing. During production, the workpiece undergoes hardening; it is necessary to relieve the stress from the metal. After heating the oven to 600-700 °C, you need to put a drill in it and hold the part for 3 hours. Afterwards, let it cool on its own.
2. After cooling, the workpiece is ready for use. Heat the oven to 1000 °C and place the drill in it. Having acquired an orange color, the workpiece is heated, we take it out with pliers and clamp it in a vice with the shank. Use a wrench to grab the top of the drill and turn the metal into a straight plane. All movements must be performed quickly - cooling of the workpiece is unacceptable.
3. The product cannot be allowed to cool down; by constantly heating it, we begin to forge. Keep an eye on the color of the metal; if it has tarnished a little, put it straight into the oven. We cut it into a strip of the required thickness of 3-4 mm. We extend the shank in length.
4. Having reached the desired butt, we begin to work on the tip and blade. We gradually round it in the area where the blade rises, pulling the metal towards the tip. The process is complex and requires certain skills.
5. Forging of the RC is carried out with a small hammer; with careful blows, you need to achieve the minimum thickness.

The process of making a knife from a drill.

Branches in polyurethane foam insulation

An outlet in polyurethane foam insulation - consists of a steel outlet, on top of which a protective casing (outlet shell) made of polyethylene or galvanized steel is placed, and the space between the outlets is filled with polyurethane foam.

The following trade names are available: pre-insulated outlet, pre-insulated outlet, thermally water-insulated outlet, steel outlet in polyurethane foam insulation.

These products are manufactured in accordance with GOST 30732-2006.

During the production process, steel pipes are welded to the steel outlet and a polyethylene (PE) or galvanized steel (ZS) protective casing is put on. To ensure uniform distribution of the heat-insulating layer of polyurethane foam (PPU), centering supports are installed between the outlet with branch pipes and the protective shell. The resulting space is filled with polyurethane foam. This manufacturing technology is called “Pipe in Pipe”.

Purpose

Bends in polyurethane foam insulation are used in the modernization and construction of heating networks through which the working medium is circulated, having the following parameters:

• ultimate pressure: 1.6 MPa;
• maximum long-term t°: +140°С;
• short-term peak t°: +150°С;
• nominal temperature range for regulating the amount of heat supplied to consumers: +70°÷ +150°С.

Bends in polyurethane foam insulation are designed to change the direction of the thermal route.

In addition to the main purpose, bends in polyurethane foam insulation can be used for pumping gas, oil, and other liquid and gaseous media.

The laying of pipelines using bends can be carried out directly in the ground, in non-passable, semi-passable and through reinforced concrete channels, tunnels, as well as in ground and above-ground methods.

HDPE tapping welding - production.

Cutting steel pipe in production conditions.

Advantages

Polyurethane foam acting as a heat insulator has low thermal conductivity, which makes it possible to maintain a stable temperature of the transported media with minimal heat loss.

Table No. 1 shows the comparative characteristics of polyurethane foam and other common thermal insulation materials.

Thermal insulator	Density degree (kg/m3)	Thermal conductivity coefficient (W/m*K)	Porosity	Service life (years)
Polyurethane foam (PPU) hard	40-200	0,025-0,033	closed	30-50
Mineral wool	11-150	0,045-0,058	open	5
Cork board	220-240	0,035-0,060	closed	3
Foam concrete	250-400	0,025-0,035	open	10
Styrofoam	30-60	0, 037-0,050	closed	5-7

"TABLE 1" Comparison of parameters of various thermal insulation materials

Read also:  Do-it-yourself miracle shovel - drawings and dimensions, how to make it?

As follows from the table, polyurethane foam has the best thermal conductivity coefficient and estimated service life. The proven “pipe-in-pipe” production technology and low cost of components provide this product with the most favorable price/quality ratio among competing materials.

Design

The design of bends in polyurethane foam insulation must comply with GOST 30732-2006. Below, Figure 1 shows a drawing of an outlet in polyurethane foam insulation

Figure 1. Design of an outlet in polyurethane foam insulation

1 - steel pipe; 2 - insulation made of polyurethane foam; 3 - shell; 4 - centering support; 5 - steel bend; 6 - electrical insulating tube (for pipes with a steel sheath); 7 — conductor-indicator of the UEC system (shown conditionally)

The outer diameter of the steel bend (d) must be from 32 to 1420 mm.

The outer diameter of the protective shell (D) should be from 90 to 1600 mm, α is the angle of rotation of the bend, varies from 00 to 900, L is the length of the bend arm from the end to the axis.

On bends of bends, deviations of the center lines are allowed that exceed the deviations allowed on straight sections. The thickness of the outlet insulation, measured at any point, must be at least 15 mm

For ease of installation, when applying the heat-insulating layer, bare ends are left, the length of which must be within the following limits:

• 150 (-20) mm with D (diameter of the protective shell) up to 315 mm inclusive;
• 210 (-20) mm with D equal to or exceeding 400 mm.

Varieties

Bends in polyurethane foam insulation are divided into several types depending on the raw materials used. Depending on the use of the supporting steel pipe in the heating network, the following types of bends in polyurethane foam insulation are distinguished:

• bends with electric-welded pipes GOST 10704, 10705, 10706 in polyurethane foam insulation;
• bends with seamless hot-deformed pipes GOST 8731, 8733 in polyurethane foam insulation;
• bends with seamless cold-deformed and heat-deformed branch pipes GOST 8732, 8734 in polyurethane foam insulation;
• bends with seamless pipes for the oil refining and petrochemical industries GOST 550 in polyurethane foam insulation;
• bends with welded pipes for main gas and oil pipelines GOST 20295 in polyurethane foam insulation;

Source: https://www.teploenergoplast.ru/catalog/teplotrassa/otvody-v-ppu-izolyatsii/

Selecting a profile

Making stairs from metal has been around for a long time, and this is not a new idea at all. When choosing this design, special attention was paid to the metal corner and channel.

The assembly principle that has been used for years:

• Two channels were placed parallel to one another;
• Using a metal corner, the contours between the channels were welded;
• A step made of wood or a metal relief structure was attached.

Judging by many years of practice, we can say that the use of a metal corner is short-lived, since it deforms under the influence of loads. They found an alternative to the metal corner, and this is a metal profile.

Hint: It is best to use a square metal pipe with a cross-section of 40*60 for stairs; this is the most suitable option. If you use a pipe with a smaller cross-section, the result will be the same as in the case of a corner, but if you choose very large ones, they will look ugly and rough.

Advantages of a staircase made of metal profiles:

An interfloor staircase is a highly complex structure that requires competent calculation. Errors made during design significantly reduce not only the convenience, but also the safety of the product. As a rule, a staircase from a profile pipe is made by professionals who are thoroughly versed in the specifics of designing staircase structures. It is quite possible to make a staircase from a profile pipe, the main thing is to create drawings and perform the calculations correctly.

Round Steel Vent Vent 90° Degree

A 90° round ventilation outlet (another name is an elbow) is designed to change the route of the ventilation duct by 90° degrees. Round cross-section bends for general ventilation are made of galvanized steel . The ventilation duct is a shaped air duct , therefore it is characterized by all the properties of round air ducts: round ventilation ducts create less air resistance compared to rectangular analogues.

Diagram of a 90° degree round vent

Symbol in the diagram:

D —product diameter, mm;

R — turning radius, mm.

Technical characteristics of round ventilation ducts AeroStar

From us you can buy high-quality ventilation ducts made of steel , which we been producing for 15 years .

find out steel bends price list.

The turning radius (R) of a standard elbow manufactured by us is equal to its diameter: R=D.

Manufacturing of round ventilation ducts to order

We make non-standard ventilation products to order . To buy such a product, as well as to clarify the price, you need to send a drawing of the part to us by email . Possible modifications:

• Changing the radius (R) of the product
• Changing the rotation angle (60°, 30°, 15°, etc.)
• Changing the length of the neck of the product
• Manufacturing a product with a transition function (retraction-transition)
• Manufacturing products of non-standard diameter

Connection types for round steel vent

All AeroStar round shaped air ducts a nipple connection as standard , due to the fact that the outer diameter of the shaped air ducts is smaller than the internal diameter of straight air ducts, they are simply inserted inside - which speeds up and simplifies the installation of the ventilation system. In addition, we produce shaped air ducts with other types of connections. Possible connection options:

• Nipple (the product has nipple dimensions, i.e. it is inserted into the air duct)
• Flanged
• At the request of the customer (the product is put on the air duct)

Buy round ventilation ducts made of steel

We are engaged in the sale of round ventilation ducts, both from production and from warehouse; products made of galvanized steel up to 355 diameter are always available in stock.

You can find out the price for round ventilation ducts the price list section of the website.

To place an order, find out the price and buy the necessary ventilation products just send your request to us by email [email protected] or call: (812) 313-41-15

Source: https://aerostar-spb.ru/catalog/round_ventilation/143/

Finishing

After finishing the forging manipulations, let the blade cool. You should move on to grinding work. We remove carbon deposits and level the slopes. We do preliminary sharpening of the blade. Final works:

1. An angle grinder with a cutting wheel will definitely help you adjust the shank to the mounted handle. Mark and cut as required.
2. An important stage that gives the blade the quality of hardness and wear resistance is hardening. After heating the workpiece to 500-700 °C, it should be quickly lowered into oil. Be careful - the oil actually splashes and there is a risk of fire.
3. Tempering of the blade is mandatory; it should be carried out at a temperature of 200-220 °C for 2-3 hours. Upon completion, the blade should be treated with fine-grained sandpaper.
4. We make the handle from a block of wood, drilling holes in it and fitting the shank. It should be given the necessary shape. After making sure that the parts match perfectly, pour epoxy glue into the hole in the handle and hammer the blade with the shank inward. Let the glue dry for a day and treat the handle with oil or special impregnation.
5. The final stage is sharpening the blade for finishing. It is preferable to perform these manipulations on diamond stones. The process is long and tedious, but the result is magnificent.

Steel bends: products for changing the direction of the pipeline

Steel bends are products that are used to change the direction of various pipelines. They are pipe segments bent at the desired angle. They are usually carried out using special pipe bending machines and are mounted on the pipeline by butt welding. The operational scope of these parts is incredibly wide, but they are most often used in the installation of oil, gas and water supply communications.

Bends for steel pipes are made of stainless steel, alloy steel, and they can also have a protective zinc coating

Scope of use of steel bends

Let's consider the main areas in which these products are used:

• plumbing systems;
• heating communications;
• industrial highways for various purposes;
• oil and gas industry;
• chemical industry;
• pumping stations.

Such products are used for wiring communications for any purpose, however, not all of their types are suitable for certain pipelines. For example, for laying main networks, as a rule, steeply curved seamless, stamped-welded, and bent products made of stainless steel, alloyed, and galvanized bends are used. This is due to the fact that such communications have large cross-sectional dimensions and can operate at high pressure in the working environment.

Helpful information! Welded bends are used for various communications. The pressure in such pipelines does not exceed 2.5 MPa. The cross-sectional indicators in such pipelines are usually more than 1000 mm.

For household communications, steeply curved or bent types of bends are an excellent solution. And point products are very popular when installing pipelines at enterprises that produce various mineral fertilizers.

Such a part as a bend can be found on a pipeline of any type and purpose.

As mentioned above, such a product provides rotation of the structure. Bends are used not only in pipelines, but also in communications responsible for cleaning indoor air. The most popular in this case is a galvanized ventilation outlet.

Advantages of steel bends

Pipeline fittings are widely used in any installation, and steel turning parts are considered the backbone of any pipeline. Along with tees and transition elements, they play an important role in connecting communications and increasing its strength.

Let's look at the main advantages of these products:

• with the help of these products a smooth rotation of the pipeline structure is made;
• the characteristics of metal bends allow them to be used in difficult operating conditions - they have high strength characteristics and can also be operated at high pressure;
• steel products are resistant to temperature fluctuations;
• the cost of such bends is quite affordable;
• have a long service life when used in aggressive industrial conditions.

Why do chimneys get clogged?

The accumulation of soot and tar is quite difficult to avoid; over time, such deposits will make themselves felt, draft may become poor, and smoke in the premises will affect the comfort of living in the house.

The most dangerous thing can be safely called the ignition of small elements in soot when their volumes are large; everyone takes fire safety seriously, so the problem must be eliminated in a timely manner.

Among the subjective reasons, it is worth highlighting the following:

1. Coal and firewood were of poor quality.
2. Use for heating household waste such as plastic, rubber and similar things.
3. The operating mode of the device is selected incorrectly.
4. Gross mistakes were made during the construction of the device.
5. Burning resinous fuel, spruce, pine.
6. Using wet logs.

Based on these factors, the owners try to eliminate the problem, but with these actions they only delay the moment of cleaning the canal.

Without decisive action, it will not be possible to eliminate large particles, which is why environmentally friendly means for manual pipe cleaning are in great demand. All manipulations can be done independently and achieve maximum results in a short period of time.

Main settings

A metal staircase made from a profile pipe will be perfectly manufactured with proper design, if the engineer has selected in advance:

— Number of spans; — The value of the slope angle, which does not change for each span. Their number does not matter, the main thing is the unity of the indicator; — Span height; — Characteristics of steps: width, number, height; — Method of connection in the presence of at least two spans (winder steps or platform); — Dimensions of the opening for the stairs.

The calculation is based on individual measurements, since they will differ in a particular room. A metal frame for a staircase made from a profile pipe must be created taking into account the average step length. Otherwise, using the stairs will be uncomfortable.

Another important aspect for a person is the choice of step parameters. Having taken all measurements and performed calculations, you need to draw a drawing, indicating all the dimensions of the final structure.

Let's consider options on how to make a staircase from a profile pipe. The type of construction in all cases is kosour. The type of staircase can be absolutely any: straight, rotary or spiral. It depends on your home design and interior design.

Stages of work

Steps are welded onto the two main corrugated pipes, which will serve as supports. To begin with, first, and then, after the necessary check for the absence of irregularities, the steps are finally fixed.

Then the second part of the stepladder is made in the same way.

The two parts are connected using a hinged canopy.

On the middle part of the structure there are holes to which a belt will be attached to secure the ladder so that it is securely held in the desired position during operation.