How to fasten timber to each other: all methods of longitudinal and transverse connection


The quality of the connection of individual wall elements affects the durability of the house, its reliability and appearance. Wooden buildings were one of the first to be erected by man, and since those ancient times he has known many ways to fasten timber together. They are still used today, along with modern methods that use special fasteners. Having studied all the known methods, you can choose from them those that seem to you the most durable and affordable.

Construction of a house from timber Source brusovoidom44.ru

Corner connections

There are different ways to connect the beams to form an angle. Previously, they were traditionally attached “into a bowl”, making the joint not at the ends, but slightly retreating from them. The result was a cross-shaped joint with ends protruding outward. But there are many ways to avoid leaving such protrusions that interfere with the exterior finishing.

Since the beam has the correct geometry with a rectangular or square cross-section, it is much easier to connect than a log. Even rounded. This shape simplifies the marking and production of grooves and allows for tight joints.

Let's look at the main options for connecting timber at an angle to each other:

  • Butt. The simplest method that does not require cutting or grooves. One beam is butted end to side of the other, in each row such joints are shifted and alternated, as in the previous photo. This connection is very fragile and requires additional fixation with perforated steel plates, staples or other fasteners. In addition, end-to-end corners, even with high-quality insulation, begin to blow out over time and let moisture in. Therefore, this method is used mainly for the construction of outbuildings and other non-residential buildings.


The joint is additionally secured with a bracket and a steel angle Source www.allremont59.ru

  • Half a tree . This type of joint is very common, as it is accessible even to inexperienced carpenters. It involves removing part of the beam from the end to half its depth. The end result is steps that overlap each other. To strengthen the joints, they are drilled through and dowels are driven into the holes. They also fasten the beams along the length of the span between the corners.


Corner connection in half a tree Source 900igr.net

  • In the paw. This fastener is very similar to the previous one, but the end is cut out not at a right angle, but at an angle.
  • Dovetail. One of the most durable and reliable ways to fasten timber together. It consists of a tenon-groove locking device. Moreover, the spikes have the shape of a trapezoid, which increases the area of ​​​​conjugation of the two elements and does not allow them to “spread apart”.


The shape and size of the tenon are selected so that it fits tightly into the groove formed by two tenons of the transverse rims Source stroyfora.ru

  • Root thorn. Otherwise, such a connection is called a “frying pan” or “warm corner”, since it is windproof, without through gaps from the street to the room. In this case, the locking T-shaped connection is made secret by cutting out a rectangular or trapezoidal groove in the horizontal plane not to the entire thickness of the beam, but only to half. The tenon of the second beam repeats its shape. This joint is called a blind pan and is used to fasten the outer corners of a house. When constructing internal partitions, an open frying pan is often used, cutting a groove along the entire thickness of the beam. Additional strength is provided by driving a dowel into the lock.


Warm corner with rectangular and trapezoidal tenon Source i0.wp.com
See also: Catalog of timber house projects

  • Into the bowl. The method is similar to joining a half-tree, but the grooves are cut not at the ends of the crowns, but with an indentation from them and the formation of residues protruding beyond the perimeter of the walls. The groove can only be on one side of each crown - and this is the simplest and easiest option to implement. Cutting can be done on two opposite faces, or on all four.

For reference! Four-sided grooves are quite difficult to manufacture; they are usually made in the factory when ordering a log house according to a finished project.


One of the options for connecting timber to each other using the “bowl” method with four-sided grooves Source utwood.su
These methods are used for any corner joints, not exclusively rectangular ones. Simply, the ends of the beams are first sawed off to form bevels that give the desired angle at the junction.

Briefly about the main thing

Due to its technical characteristics, wooden beams are actively used in the construction of houses and the assembly of various structures.

In the case of log houses, the workpieces can be fastened without the use of additional devices by sawing (cutting out) grooves and counter tenons.

Outbuildings can be assembled end-to-end, but metal clamps or spiked plates are required to tie the beams together.

If you need to secure the timber to a wooden base, you can use nails and screws, metal plates, corners and supports.

To fix timber on a base with other compositions, screws with various dowels (plastic, wood, metal), anchor bolts or studs with nuts, and chemical anchors are used.

Connections in length

The standard maximum size of timber is 6 meters in length with different sections. This is often not enough to build the walls of a large house, install rafters or lay floor beams. You have to splice 2 or even 3 elements in the longitudinal direction. And it’s one thing when it is a crown that has support under it in the form of a foundation or an underlying crown, and another thing if there is no such support. We have to decide how to splice the beam along its length in order to withstand the load not only from its own weight, but also from the structures resting on it.

Such problems are solved in ways similar to those already described. The fastening is simply done not at an angle, but along the beams.


During the construction of canopies, gazebos and other similar structures, the jointed timber may not have any support Source i.ytimg.com

See also: Catalog of companies that specialize in the construction of houses made of timber

  • Half a tree. A fastening unit already familiar to you, when symmetrical straight notches are cut from the ends up to half the thickness of the beam. Splicing with oblique notches will be more reliable. But in any case, additional fixation with plates, pins or dowels is required.
  • Oblique castle. In this case, the connected ends are also cut obliquely, but the cuts are not flat, but stepped in shape with certain parameters for each protrusion. When combining two beams, they must exactly repeat each other. “Sliding” is prevented by an already proven method - driving dowels into the joint. Without a special tool, solving the problem of how to connect 100x100 beams together in this way is almost impossible.
  • Straight patch lock. At the ends of the beams, peculiar hooks are cut along their entire width. This is the most reliable splicing method for hanging beams.


Straight and oblique lock Source i1.wp.com

  • Root thorn . This is the same type of connection that was described in the previous chapter. The spike can be either rectangular or trapezoidal. The trapezoid is much more reliable, as it prevents vibrations in the horizontal direction.
  • On the key. If, when installing a main tenon, a tenon is formed at the end of one beam, and a groove is selected in the other, then in this case two grooves are made, the beams are laid end-to-end, and a key is driven into the resulting hole, repeating its shape. It is pre-coated with wood glue or PVA glue to increase the strength of the joint.

Note! When building walls, it is not enough to decide how to connect the beams together along the length. It is necessary to shift the joints relative to each other so that they do not coincide along the vertical line in adjacent crowns.

The production of locking joints is noticeably simplified and accelerated if you do not mark each beam individually, but make a template from thin and dense sheet material.

Beam holders

Like other perforated parts, the beam holders are made of galvanized steel.

They have high anti-corrosion characteristics.

They are used as fasteners for cross surfaces . For example, for fixing ceilings, floors and floors.

As well as the roof truss system. Beam holders are also needed to connect the rafters to the supporting beams.

The thickness of the parts, as well as the reinforced corners, reaches 2.5-3 millimeters.

The holders also have holes for screws, which greatly simplify the installation process and reduce time.

Connection fastener

With the advent of modern fasteners made of durable alloy and galvanized steel, many construction processes have been simplified, including the installation of reliable connecting units in timber structures. Some of them have been used for a long time and are traditionally popular. Others appeared relatively recently, so they may be unknown to people whose profession and interests are not related to construction.

Traditional fasteners

The simplest and most reliable of them are dowels or dowels made of hard wood. They blend perfectly with the base material without causing it to deform, crack or rot. In combination with adhesives, they allow for durable fastening.


Assembling a log house on steel dowels Source remontik.org

Pins are also metal. Their main advantage is their high strength and durability, which is why they are often used to fasten timber crowns vertically.

Nails and staples, which used to be almost the only types of fasteners for wood, are now trying not to be used in the construction of permanent buildings, since the ferrous metal from which they are made is incompatible with wood. It corrodes easily, damaging the wood and gradually deteriorating. For the same reason, it is not recommended to use homemade dowels cut from reinforcing bars.

Modern fasteners

A wide variety of fasteners are made from perforated rolled steel with a thickness of at least 2 mm with an anti-corrosion coating. It is made from:

  • plates of different lengths and widths with holes for screws and anchors. A large assortment of standard sizes allows you to solve problems such as connecting beams together along a length of 150 by 150, fastening rafters at the ridge part, or strengthening a sagging joint without lower support;


Galvanized connecting plate Source www.sibwindows.ru

How to choose fasteners for wooden beams?

Specific fasteners are designed for each type of work; they should be used for their intended purpose, otherwise the strength of the structure will be compromised. Screws and anchors are used together with plates and angles. They also need to be selected and used correctly.

To do this, at the stage of drawing up the project, calculations are made, the maximum load on a beam or other element, and the ability to withstand loads are determined. If you want the fasteners to be invisible in the interior, you should choose hidden varieties.

In addition to modification, quality should be considered.
Products must be made of high quality galvanized steel. There should be no defects on the surface. KrepMetiz has a large selection of certified products for construction. < Previous Next >

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]